C. TCAS Test Do the BITE test of the TCAS (Ref. AMM TASK 34-43-00-740-001).
4. Fault Isolation
_______________
**ON A/C 001-049, 101-105, 151-199,
A. If the ATC1 test gives the maintenance message ATC-1:NO DATA FROM TCAS, and if the TCAS test gives the maintenance message TCAS (1SG): - on the center pedestal, on the ATC/TCAS control unit, set the ATC2 to
on and do the BITE test of the ATC (system 2) (Ref. AMM TASK 34-52-00-740-004).
(1) If the test gives the maintenance message ATC-2:NO DATA FROM TCAS:
- replace the CMPTR-TCAS (1SG) (Ref. AMM TASK 34-43-34-000-001) and (Ref. AMM TASK 34-43-34-400-001)
- if the fault continues, do a check and repair the suppressor coaxial cable from the TCAS computer (1SG) pin AC/12 to the connector 150VC (Ref. AWM 34-43-05).
(2) If the test is OK, do the BITE test of the TCAS (Ref. AMM TASK 34-43-00-740-001):
- if the test is OK, do a check and repair the suppressor coaxial cable from the ATC transponder 1 (1SH1) pin AC/12 to the connector 150VC (Ref. AWM 34-52-03).
R **ON A/C 051-099, 106-149, 201-299, 301-399, 401-499,
R A. If the ATC1 test gives the maintenance message TCAS(1SG)/ATC1(1SH1) and
R if the TCAS test gives the maintenance message TCAS (1SG):
R - on the center pedestal, on the ATC/TCAS control unit, set the ATC2 to
R on and do the BITE test of the ATC (system 2) (Ref. AMM TASK 34-52-00-R 740-004).
R (1) If the test gives the maintenance message TCAS(1SG)/ ATC2(1SH2)
R - replace the CMPTR-TCAS (1SG) (Ref. AMM TASK 34-43-34-000-001) and
R (Ref. AMM TASK 34-43-34-400-001)
R - if the fault continues, do a check and repair the suppressor
R coaxial cable from the TCAS computer (1SG) pin AC/12 to the
R connector 150VC (Ref. AWM 34-43-05).
R (2) If the test is OK, do the BITE test of the TCAS (Ref. AMM TASK 34-43-R 00-740-001):
R - if the test is OK, do a check and repair the suppressor coaxial
R cable from the ATC transponder 1 (1SH1) pin AC/12 to the connector
R 150VC (Ref. AWM 34-52-03).
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1R EFF : ALL ∞∞34-43-00∞∞∞∞∞∞∞∞∞∞Page 250
Aug 01/05 CESR **ON A/C ALL
B. Do the test given in para. 3.
Loss of the Suppressor Function between ATC2 and TCAS
1. Possible Causes
_______________
- CMPTR-TCAS (1SG)
- suppressor coaxial cable
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
AMM 34-43-00-740-001 BITE Test of the TCAS
AMM 34-43-34-000-001 Removal of the TCAS Computer (1SG)
AMM 34-43-34-400-001 Installation of the TCAS Computer (1SG)
AMM 34-52-00-740-004 BITE Test of the ATC
AWM 34-43-05
AWM 34-52-03
3. Fault Confirmation
__________________
A. Make sure that this(these) circuit breaker(s) is(are) closed:
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------
49VU COM NAV/ATC/1 5SH1 G11 R
R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 301-399,
R 121VU COM NAV/TCAS 4SG K10
R **ON A/C ALL
R 121VU COM NAV/ATC/2 5SH2 K07
B. ATC2 Test On the center pedestal, on the ATC/TCAS control unit, set the ATC2 to on and do the BITE test of the ATC (system 2) (Ref. AMM TASK 34-52-00-740-004).
C. TCAS Test Do the BITE test of the TCAS (Ref. AMM TASK 34-43-00-740-001).
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞34-43-00∞∞∞∞∞∞∞∞∞∞Page 252
Aug 01/05 CES
4. Fault Isolation
_______________
**ON A/C 001-049, 101-105, 151-199,
A. If the ATC2 test gives the maintenance message ATC-2:NO DATA FROM TCAS, and if the TCAS test gives the maintenance message TCAS (1SG): - on the center pedestal, on the ATC/TCAS control unit, set the ATC1 to
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 導航 NAVIGATION 3(64)
