-
THE FLIGHT CONTROL SURFACES

 -
THE LANDING GEAR AND THE RELATED DOORS

 -COMPONENTS THAT MOVE.
 WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
 CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING EDGE:
_______
 -
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.

 -
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.

 -MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.
 1. Reason for the Job
__________________
 Refer to the MPD TASK: 575119-01
 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s) No specific safety barriers No specific warning notices No specific access platform 3 m (9 ft. 10 in.) 98D27803500001 1 TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER
 1EFF : ALL 1 57-51-00Page 618 1 1 Aug 01/02R 1 1 1CES 1

 B. Consumable Materials
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 11-026  GB DEF-STAN 68-148/1 SOLVENT GENERAL PURPOSE (Ref. 20-31-00) Material No. 19-003 USA AMS 3819 LINT-FREE COTTON CLOTH (Ref. 20-31-00)
 C. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
ASRM 575100 (for corrective action) 57-51-00-991-003 Fig. 604
 3. Job Set-up
__________ Subtask 57-51-00-941-051
 A. Safety Precautions
 (1)
 Install the TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER (98D27803500001) on the flap/slat control lever.

 (2)
 Put warning notices in the cockpit to tell persons not to operate the flaps or slats.

 (3) Put the safety barriers in position. Subtask 57-51-00-865-052
 B. Open, safety and tag this(these) circuit breaker(s):
 -------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU FLIGHT CONTROLS/SLT/CTL AND MONG/SYS1 5CV B06 121VU FLIGHT CONTROLS/SLT/CTL/SYS2 7CV R21
 1EFF : ALL 1 57-51-00Page 619 1 1 Aug 01/02R 1 1 1CES 1

 Subtask 57-51-00-010-051
 C. Get Access
 (1)
 Put the access platform in position below the applicable aileron, zone 575(675).

 (2)
 Remove the access panels:

 -
for the left wing, remove 575AT, 575JB, 575KB, 575LB, 575MB

 -
for the right wing, remove 675AT, 675JB, 675KB, 675LB, 675MB.

 4. Procedure
_________
 (Ref. Fig. 604/TASK 57-51-00-991-003)
 CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING
_______
 EDGE:

 -
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.

 -
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.

 -MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.
 Subtask 57-51-00-110-053
 A. Preparation for Inspection
 (1) Use a MISCELLANEOUS (Material No. 19-003), made moist with CLEANING AGENTS (Material No. 11-026) to clean the hinge fittings.
 Subtask 57-51-00-220-050
 B. Inspection
 (1)
 Examine the aileron hinge fittings to make sure that:

 -
there is no damage

 -
there is no corrosion

 -
there are no scratches and/or scores

 -the surface protection is in the correct condition.

 (2)
 Examine the aileron A-frames to make sure that:

 -
there is no damage

 -
there are no scratches and/or scores

 -
there is no corrosion

 -the surface protection is in the correct condition.
 NOTE : If necessary, refer to the ASRM (Ref. ASRM 575100) for the
____
 correct repair procedure.

 1EFF : ALL 1 57-51-00Page 620 1 1 Aug 01/02R 1 1 1CES 1
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM WINGS 機翼3(85)