(c)
Hold the flanged nuts (7) and install the nuts (6).
(d)
TORQUE the nuts (6) to between 3.7 and 4.0 m.daN (27.28 and 29.49 lbf.ft).
(e)
Install the new cotter pins (5) then safety the nuts (6) and (7) with MISCELLANEOUS (Material No. 19-010).
(8)
Remove the support from the flap track beam (1).
(9) Measure the dimension Z again.
**ON A/C ALL
5. Close-up
________ R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
Subtask 57-51-33-410-051
A. Close Access
(1)
If necessary, install the No.2 flap track actuator (Ref. TASK 27-54-49-400-002).
(2)
Install the carriage on the applicable No.2 flap track beam (Ref. TASK 27-54-46-400-001).
(3) Install the fairings of the No.2 flap track (Ref. TASK 57-55-11-400-001).
R **ON A/C 301-399,
R Subtask 57-51-33-410-051-A
R A. Close Access
R R (1) If necessary, install the No.2 flap track actuator (Ref. TASK 27-54-49-400-002).
R R (2) Install the carriage on the applicable No.2 flap track beam (Ref. TASK 27-54-46-400-001).
R R (3) Install the fairings of the No.2 flap track (Ref. TASK 57-55-11-400-004).
R **ON A/C ALL
Subtask 57-51-33-942-051
B. Removal of Equipment
(1) Make sure that the work area is clean and clear of tool(s) and other items.
(2) Remove the LOCKING TOOL - FLAP/SLAT CONTROL LEVER from the slat/flap control lever.
(3) Remove the warning notice(s).
(4) Remove the access platform(s).
(5) Remove the safety barriers.
(6) Remove the ground support and maintenance equipment, the special and standard tools and all other items.
TASK 57-51-33-000-003
Removal of the No.3 Flap Track Beam
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
GEAR.
CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING EDGE:
_______
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.
-MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific safety barriers
No specific warning notices
No specific access platform 4 m (13 ft. 1 in.)
98D57004037000 1 EXTRACTOR FLAP SPIGOT
R 98D57004096000 1 EXTRACTOR FLAP SPIGOT B. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
27-54-46-000-001 Removal of the Nos. 2, 3 and 4 Flap Carriages 27-54-49-000-003 Removal of the Flap Track 3 Actuator 6221CM(6271CM) 57-55-11-000-001 Removal of the Flap Track Fairings Nos. 2, 3 and 4 57-55-11-000-004 Removal of the Flap Track Fairings Nos. 2, 3 and 4
**ON A/C 301-399,
57-51-33-991-002-A Fig. 402 R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
57-51-33-991-004 Fig. 404
**ON A/C ALL
3. Job Set-up
__________
**ON A/C 301-399,
(Ref. Fig. 402/TASK 57-51-33-991-002-A) R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
(Ref. Fig. 404/TASK 57-51-33-991-004)
**ON A/C ALL
Subtask 57-51-33-941-052
A. Safety Precautions
(1)
Put warning notices in the cockpit to tell persons not to operate the flaps or slats.
(2)
Put the safety barriers in position.
No.s 3 and 4 Flap Track Beams
Figure 404/TASK 57-51-33-991-004
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 57-51-33Page 449 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499, 中國航空網 m.k6050.com 航空翻譯 www.aviation.cn 本文鏈接地址：A320飛機維護手冊 AMM WINGS 機翼3(148)
