(2)
Remove the TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER from the flap/slat control lever.
(3)
Remove the access platform(s).
(4)
Remove the safety barriers.
(5)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
1EFF : ALL 1 57-51-00Page A648 1 1 Nov 01/04R 1 1 1CES 1
TASK 57-51-00-210-002
Detailed Visual Inspection of Outer Wing Trailing Edge Spoilers 1, 2, 3, 4 and 5 Hinge Pins
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING EDGE:
_______
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.
-MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.
1. Reason for the Job
__________________
Refer to the MPD TASK: 575106-03
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific safety barriers No specific warning notices No specific adjustable access platform 4 m (13 ft. 1 in.) 98D27803500001 1 TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER
1EFF : ALL 1 57-51-00Page A649 1 1 Nov 01/04R 1 1 1CES 1
B. Consumable Materials
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
Material No. 11-026 GB DEF-STAN 68-148/1
SOLVENT GENERAL PURPOSE (Ref. 20-31-00)
Material No. 19-003 USA AMS 3819
LINT-FREE COTTON CLOTH (Ref. 20-31-00)
C. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
27-64-41-000-001 Removal of the Spoiler 1
27-64-41-400-001 Installation of the Spoiler 1
27-64-42-000-001 Removal of the Spoiler 2
27-64-42-400-001 Installation of the Spoiler 2
27-64-43-000-001 Removal of the Spoiler 3
27-64-43-400-001 Installation of the Spoiler 3
27-64-44-000-001 Removal of the Spoiler 4
27-64-44-400-001 Installation of the Spoiler 4
27-64-45-000-001 Removal of the Spoiler 5
27-64-45-400-001 Installation of the Spoiler 5
ASRM 575100 (for corrective action)
R 57-51-00-991-024 Fig. 625
3. Job Set-up
__________
NOTE : During this procedure, you will remove the two inner hinge pins only
____ for each spoiler. It is not necessary to remove the outer hinge pins.
Subtask 57-51-00-941-079
A. Safety Precautions
(1)
Install the TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER on the flap/slat control lever.
(2)
Put warning notices to tell persons not to operate the flaps or slats.
(3)
Put the safety barriers in position.
Subtask 57-51-00-010-080
B. Get Access
(1)
Put the adjustable access platform below the applicable trailing edge, zones 573(673).
(2)
Remove the applicable access panels:
-
for the left wing, remove 573CB, 575AB, 575DB, 575EB, 575GB
-
for the right wing, remove 673CB, 675AB, 675DB, 675EB, 675GB.
4. Procedure
_________
R (Ref. Fig. 625/TASK 57-51-00-991-024)
CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING
_______
EDGE:
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.
-MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.
Subtask 57-51-00-020-080
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM WINGS 機翼3(116)
