B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
R Material No. 07-003 R ABRASION RESISTANT COATING (TEFLON POLYURET) (Ref. 20-31-00)
Material No. 11-004 USA MIL-T-81533
1.1.1TRICHLOROETHANE (METHYL CHLOROFORM)
(Ref. 20-31-00)
Material No. 19-003 USA AMS 3819
LINT-FREE COTTON CLOTH (Ref. 20-31-00)
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 19-011 SCOTCH BRITE PADS (Ref. 20-31-00)
C. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
27-80-00-866-004 Extending the Slats on the Ground 27-80-00-866-005 Retracting the Slats on the Ground 51-75-12-300-001 Repair of Major Paint Damage on Light Alloy and
Composite Material 57-43-11-991-001 Fig. 701
3. Job Set-up
__________ Subtask 57-43-11-941-050
A. Safety Precautions
(1) Put warning notices in the cockpit to tell persons not to operate the flaps or slats.
(2) Put the safety barriers in position. Subtask 57-43-11-860-050
B. Aircraft Maintenance Configuration
(1)
Fully extend the slats (Ref. TASK 27-80-00-866-004).
(2)
Make sure that the LOCKING TOOL - FLAP/SLAT CONTROL LEVER (98D27803000000) is installed on the flap/slat control lever.
(3)
Put the access platform below the applicable wing leading edge at slat 2, zone 512 (612).
1EFF : ALL 1 57-43-11Page 702 1 1 Feb 01/99R 1 1 1CES 1
Subtask 57-43-11-865-052
C. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU FLIGHT CONTROLS/SLT/CTL AND MONG/SYS1 5CV B06 121VU FLIGHT CONTROLS/SLT/CTL/SYS2 7CV R21
4. Procedure
_________
(Ref. Fig. 701/TASK 57-43-11-991-001)
Subtask 57-43-11-110-050
A. Cleaning and Preparation of Slat 2 Surfaces
WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER SPECIAL
_______ MATERIALS ONLY WITH A GOOD SUPPLY OF AIR. OBEY THE MANUFACTURERS INSTRUCTIONS. PUT ON PROTECTIVE CLOTHING. DO NOT GET THEM IN YOUR MOUTH. DO NOT SMOKE. DO NOT BREATHE THE GAS. THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN IRRITANT. GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED.
WARNING : IF YOU GET THE FLUID ON YOUR SKIN OR IN YOUR EYES:
_______
-FLUSH IT AWAY WITH CLEAN WATER
-GET MEDICAL AID.
(1) Cleaning
WARNING : CLEANING SOLVENTS ARE FLAMMABLE, VOLATILE, TOXIC. THEY
_______ SHOULD BE USED WITH ADEQUATE VENTILATION. AVOID PROLONGED BREATHING OF VAPORS AND REPEATED OR PROLONGED CONTACT WITH THE SKIN, OR CLOTHING.
(a) Use a MISCELLANEOUS (Material No. 19-003), made moist with CLEANING AGENTS (Material No. 11-004) to clean the grease from the slat surface.
-Apply the CLEANING AGENTS (Material No. 11-004) to the cloth, not the cloth to the CLEANING AGENTS (Material No. 11-004). This will prevent the transfer of contamination.
1EFF : ALL 1 57-43-11Page 703 1 1 Feb 01/99R 1 1 1CES 1
Slat No. 2 - Painting Area and Dimensions.
Figure 701/TASK 57-43-11-991-001
1EFF : ALL 1 57-43-11 Page 704
1 1 Feb 01/98
1 1
1CES 1
- Carefully clean a small area at a time and remove the CLEANING AGENTS (Material No. 11-004) before it becomes dry. Use a new MISCELLANEOUS (Material No. 19-003) frequently to make sure that the dirt is not put back on the surface. - If necessary, use a brush to clean out the holes and edges.
(b) Clean the slat surface again, where there is contamination remaining.
(c) When the area is clean, flush with clean water.
(d) Use a new dry MISCELLANEOUS (Material No. 19-003) to carefully dry the area.
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM WINGS 機翼3(41)
