-
THE FLIGHT CONTROLS

 -
THE FLIGHT CONTROL SURFACES

 -
THE LANDING GEAR AND THE RELATED DOORS

 -COMPONENTS THAT MOVE.
 WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
 GEAR.

 1. Reason for the Job
__________________
 Self Explanatory
 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific plastic spatula
 No specific warning notices
 No specific access platform 3 m (9 ft. 10 in.)
 No specific Torque Wrench : range 0.20 to 3.60 m.daN

 (2.00 to 26.00 lbf.ft)
 B. Consumable Materials
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 09-013  USA MIL-PRF-81733 TYPE I CLASS A
 CORROSION INHIBITING BRUSH CONSISTENCY
 (Ref. 20-31-00)

 Material No. 09-016  USA MIL-PRF-81733D TYPE II CLASS B
 CORROSION INHIBITING FILLET CONSISTENCY
 (Ref. 20-31-00)

R Material No. 11-003  USA ASTM D 740 METHYL-ETHYL-KETONE (Ref. 20-31-00) -------------------------------------------------------------------------------

REFERENCE  DESIGNATION
 -------------------------------------------------------------------------------
Material No. 19-003  USA AMS 3819
 LINT-FREE COTTON CLOTH (Ref. 20-31-00)

 C. Expendable Parts
 -------------------------------------------------------------------------------
FIG.ITEM |DESIGNATION  |IPC-CSN
 -------------------------------------------------------------------------------
1 tab washer 57-44-21 02 -010A 2 nut 57-44-21 02 -010A 3 nut 57-44-21 02 -010A 4 tab washer 57-44-21 02 -010A 5 spherical bearing 57-44-21 02 -010A 6 nut 57-44-21 02 -010A 7 tab washer 57-44-21 02 -010A 8 spherical bearing 57-44-21 02 -010A 9 spherical bearing 57-44-21 02 -010A
 D. Referenced Information
 -------------------------------------------------------------------------------
REFERENCE  DESIGNATION
 -------------------------------------------------------------------------------
27-84-00-710-001 Operational Test of the Slat System
 27-84-65-000-001 Removal of the No. 3 Slat
 27-84-65-400-002 Installation of the No. 3 Slat
 57-44-21-991-001 Fig. 401

 3. Job Set-up
__________
 Subtask 57-44-21-941-051
 A. Safety Precautions
R (1) Make sure warning notices are in position in the cockpit to tell R persons not to operate the flaps or slats.
 (2) Make sure that the safety barriers are in position.

 Subtask 57-44-21-860-050

 B. Aircraft Maintenance Configuration
 (1)
 Make sure that the access platform is in position below the applicable slat 3, zone 513(613).

 (2)
 Make sure that the TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER (98D27803500001) is installed on the slat/flap control lever.

 (3)
 Make sure that the No. 3 slat has been removed (Ref. TASK 27-84-65-000-001).

 Subtask 57-44-21-865-051
 C. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged
 -------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU FLIGHT CONTROLS/SLT/CTL AND MONG/SYS1 5CV B06 121VU FLIGHT CONTROLS/SLT/CTL/SYS2 7CV R21
 4. Procedure
_________
 (Ref. Fig. 401/TASK 57-44-21-991-001)
 Subtask 57-44-21-420-051
 A. Preparation For Installation
 WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER SPECIAL
_______ MATERIALS ONLY WITH A GOOD SUPPLY OF AIR. OBEY THE MANUFACTURERS INSTRUCTIONS. PUT ON PROTECTIVE CLOTHING. DO NOT GET THEM IN YOUR MOUTH. DO NOT SMOKE. DO NOT BREATHE THE GAS. THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN IRRITANT. GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED.
 (1) Use a plastic spatula to remove the sealant from the component interfaces.
 1EFF : ALL 1 57-44-21Page 407 1 1 May 01/01R 1 1 1CES 1

 (2) Clean the component interfaces and/or the adjacent area with a MISCELLANEOUS (Material No. 19-003) made moist with CLEANING AGENTS (Material No. 11-003).
 (3) Do an inspection of the component interface and/or the adjacent area.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM WINGS 機翼3(54)