Subtask 57-51-00-260-050
B. Inspection
(1) Do a special detailed inspection of the outer wing trailing edge, aft of the rear spar, above the MLG reinforcing (Ref. NTM 57-51-60 PART 2) and (Ref. NTM 57-51-60 PART 6).
NOTE : If necessary, refer to the ASRM (Ref. ASRM 575100) for the
____ correct repair procedure. If the defect is not included in this repair, you must request a procedure from Airbus Industrie.
5. Close-up
________
**ON A/C 001-049, 051-061, 101-103, 201-203,
Subtask 57-51-00-410-070
A. Close Access
(1)
Install the applicable secondary hinged fairing (Ref. TASK 32-12-13-400-002).
(2)
Make sure that the work area is clean and clear of tool(s) and other items.
(3) Close the applicable access panel 574AB(674AB). R **ON A/C 062-099, 104-149, 151-199, 204-299, 301-399, 401-499,
Subtask 57-51-00-410-070-A
A. Close Access
(1)
Install the applicable secondary hinged fairing (Ref. TASK 32-12-13-400-002).
(2)
Make sure that the work area is clean and clear of tool(s) and other items.
(3)
Install the applicable access panel 574AB(674AB).
**ON A/C ALL
Subtask 57-51-00-865-104
B. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 6CV, 8CV.
Subtask 57-51-00-942-068
C. Removal of Equipment
(1)
Remove the access platform(s).
(2)
Remove the TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER from the flap/slat control lever.
(3)
Remove the warning notice(s).
(4)
Remove the safety barriers.
(5)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
1EFF : ALL 1 57-51-00Page A606 1 1 May 01/04R 1 1 1CES 1
TASK 57-51-00-220-011
Special Detailed Inspection of Outer Wing Bottom Skin Lower Surface Aft of the Rear Spar Under the Pylon Fairing
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
1. Reason for the Job
__________________
Refer to the MPD TASK: 575163-01
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific safety barriers No specific warning notices No specific access platform 3.0 m (9 ft. 10 in.) 98D27803500001 1 TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 11-026 GB DEF-STAN 68-148/1
SOLVENT GENERAL PURPOSE (Ref. 20-31-00) Material No. 19-003 USA AMS 3819
LINT-FREE COTTON CLOTH (Ref. 20-31-00)
1EFF : ALL 1 57-51-00Page A607 1 1 May 01/04R 1 1 1CES 1
C. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
54-54-00-000-001 Removal of the Aft Fixed Fairing
54-54-00-400-001 Installation of the Aft Fixed Fairing
NTM 57-51-63 PART 6
ASRM 575100 (for corrective action)
R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
57-51-00-991-019 Fig. 618
**ON A/C ALL
3. Job Set-up
__________
Subtask 57-51-00-941-069
A. Safety Precautions
(1)
Install the TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER (98D27803500001) on the flap/slat control lever.
(2)
Put the safety barriers in position.
(3)
Put warning notices in the cockpit to tell persons not to operate the flaps or slats.
Subtask 57-51-00-010-070
B. Get Access
(1)
Put the access platform below the applicable engine pylon, zone 470(480).
(2)
Remove the applicable aft fixed fairing (Ref. TASK 54-54-00-000-001).
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM WINGS 機翼3(105)
