3. Job Set-up
__________
NOTE : During this procedure, you will remove the two inner hinge pins only
____ for each spoiler. It is not necessary to remove the outer hinge pins.
Subtask 57-51-00-941-077
A. Safety Precautions
(1)
Install the TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER (98D27803500001) on the flap/slat control lever.
(2)
Put warning notices in the cockpit to tell persons not to operate the flaps or slats.
(3) Put the safety barriers in position. Subtask 57-51-00-010-079
B. Get Access
(1)
Put the adjustable access platform below the applicable wing trailing edge, zone 573(673).
(2)
Remove the applicable access panels:
(a)
For the left wing, remove:
-573CB (Ref. TASK 57-51-37-000-002)
-575AB, 575DB, 575EB, 575GB (Ref. TASK 57-51-37-000-004).
(b)
For the right wing, remove:
-673CB (Ref. TASK 57-51-37-000-002)
-675AB, 675DB, 675EB, 675GB (Ref. TASK 57-51-37-000-004).
4. Procedure
_________ (Ref. Fig. 603/TASK 57-51-00-991-009) CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING
_______
EDGE:
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.
-MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.
1EFF : ALL 1 57-51-00Page 614 1 1 May 01/03R 1 1 1CES 1
Spoiler Hinge Pins Figure 603/TASK 57-51-00-991-009
1EFF : 1 1R 1CES ALL 1 11 1 57-51-00 Page 615 Aug 01/00
Subtask 57-51-00-020-071
A. Remove the two applicable inner hinge pins:
-
for the spoiler 1 (Ref. TASK 27-64-41-000-001)
-
for the spoiler 2 (Ref. TASK 27-64-42-000-001)
-
for the spoiler 3 (Ref. TASK 27-64-43-000-001)
-
for the spoiler 4 (Ref. TASK 27-64-44-000-001)
-
for the spoiler 5 (Ref. TASK 27-64-45-000-001).
Subtask 57-51-00-110-074
B. Preparation for Inspection
(1) Use a MISCELLANEOUS (Material No. 19-003), made moist with CLEANING AGENTS (Material No. 11-026) to clean the two inner hinge pins.
Subtask 57-51-00-210-063
C. Inspection
(1) Examine the two inner hinge pins for:
-damage
-scratches and/or scores
-correct condition of the protective finish.
NOTE : If necessary, refer to the ASRM (Ref. ASRM 575100) for the
____
correct repair procedure.
Subtask 57-51-00-420-071
D. Install the two applicable inner hinge pins:
-
for the spoiler 1 (Ref. TASK 27-64-41-400-001)
-
for the spoiler 2 (Ref. TASK 27-64-42-400-001)
-
for the spoiler 3 (Ref. TASK 27-64-43-400-001)
-
for the spoiler 4 (Ref. TASK 27-64-44-400-001)
-
for the spoiler 5 (Ref. TASK 27-64-45-400-001).
1EFF : ALL 1 57-51-00Page 616 1 1 Aug 01/02R 1 1 1CES 1
5. Close-up
________
Subtask 57-51-00-410-080
A. Close Access
R (1) Install the applicable access panels:
R R R (a) For the left wing, install: - 573CB (Ref. TASK 57-51-37-400-002) - 575AB, 575DB, 575EB, 575GB (Ref. TASK 57-51-37-400-004).
R R R R (b) For the right wing, install: - 673CB (Ref. TASK 57-51-37-400-002) - 675AB, 675DB, 675EB, 675GB (Ref. TASK 57-51-37-400-004).
Subtask 57-51-00-942-077
B. Removal of Equipment
(1) Remove the TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER from the flap/slat control lever.
(2) Remove the warning notice(s).
(3) Remove the access platform(s).
(4) Remove the safety barriers.
(5) Remove the ground support and maintenance equipment, the special and standard tools and all other items.
TASK 57-51-00-220-001
Detailed Visual Inspection of Outer Wing Trailing Edge Aileron Hinge Fittings 1 thru 5, and 'A' Frames
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM WINGS 機翼3(84)
