R 1EFF : ALL 1 32-51-00Page 547 1 1 Aug 01/05 1 1 1CES 1 Subtask 32-51-00-865-101
D. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s):
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------121VU HYDRAULIC/BRAKING AND STEERING/SYS1/IND AND/SPLY 2GG M33 121VU ENGINE/ENG2/OIL/PRESS 2EN2 N42 121VU ENGINE/ENG1/OIL/PRESS 2EN1 N40
R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 301-399,
Subtask 32-51-00-860-074
E. Put the aircraft back to its initial configuration.
(1)
Depressurize the Green hydraulic system (Ref. TASK 29-10-00-864-001).
(2)
Lower the aircraft on its wheels (Ref. TASK 07-12-00-582-001).
(3)
Do the EIS stop procedure
(Ref. TASK 31-60-00-860-002).
(4)
On the MCDU, push the line key adjacent to the RETURN indication until the CFDS menu page comes into view.
(5)
De-energize the aircraft electrical circuits (Ref. TASK 24-41-00-862-002).
(6)
If the front of the aircraft is lifted off the ground, lower the aircraft to the ground (Ref. TASK 07-11-00-586-001).
(7)
If the nosewheels are on grease plates, move the aircraft to remove the grease plates (Ref. TASK 09-10-00-584-002).
(8)
Make sure that the work area is clean and clear of tool(s) and other items.
R 1EFF : ALL 1 32-51-00Page 548 1 1 Aug 01/05 1 1 1CES 1
R **ON A/C 401-499,
R Subtask 32-51-00-860-074-A
R E. Put the aircraft back to its initial configuration.
R (1) Depressurize the Yellow hydraulic system (Ref. TASK 29-10-00-864-
R 002).
R (2) Lower the aircraft on its wheels (Ref. TASK 07-12-00-582-001).
R (3) Do the EIS stop procedure
R (Ref. TASK 31-60-00-860-002).
R (4) On the MCDU, push the line key adjacent to the RETURN indication
R until the CFDS menu page comes into view.
R (5) De-energize the aircraft electrical circuits (Ref. TASK 24-41-00-862-
R 002).
R (6) If the front of the aircraft is lifted off the ground, lower the
R aircraft to the ground (Ref. TASK 07-11-00-586-001).
R (7) If the nosewheels are on grease plates, move the aircraft to remove
R the grease plates (Ref. TASK 09-10-00-584-002).
R (8) Make sure that the work area is clean and clear of tool(s) and other
R items.
R 1EFF : 401-499, 1 32-51-00Page 549 1 1 Aug 01/05 1 1 1CES 1 **ON A/C 001-004, 051-054,
TASK 32-51-00-820-001
Adjustment of the NWS "Zero" Position with the Adjusting Tool F26630200 for A/C with NWS Sensor (3GC,4GC) P/N C24763000, Rudder Trim Angle as Reference
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
GEAR.
1. Reason for the Job
__________________
Do this procedure when you adjust a gearbox P/N C24764000 with the adjusting tool F26630200 and when you use the Rudder Trim Angle as reference. R
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION
-------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s)
No specific nosewheel jack
No specific warning placard
No specific AC voltmeter (minimum range: 0-20V, accuracy: 1 mV,
frequency: 50-2000 Hz)
No specific 1.2m (4ft.) square steel plates
F26630200 1 ADJUSTING TOOL - NWS GEARBOX
F26792000 1 SENSOR-VOLTAGE TEST
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM LANDING GEAR 起落架8(91)
