(2)
Make sure that safety barriers are in position.
(3)
Make sure that the PARK BRK control switch is in the OFF position.
(4)
Make sure that the chocks are installed on the wheels of the main landing gear.
(5)
Make sure that the nose gear is lifted (Ref. TASK 07-12-00-582-001).
(6)
Make sure that the tire is fully deflated (Ref. TASK 12-14-32-614-001).
Subtask 32-49-15-865-054
B. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------
121VU HYDRAULIC/TIRE/PRESS 1GV M31
1EFF : 051-099, 1 32-49-15Page 413 1 1 May 01/05 1 1 1CES 1
4. Procedure
_________
(Ref. Fig. 402/TASK 32-49-15-991-002) Subtask 32-49-15-420-053
A. Installation of the Pressure Transducer Adaptor
(1)
Make sure that the packing (1) is in position on the adaptor (2). NOTE : If you install the used adaptor (2), put a new packing (1) in
____
position.
(2)
Install the pressure transducer adaptor (2) on the wheel (8).
(3)
TORQUE the adaptor (2) to between 1.35 and 1.65 m.daN (119.46 and
146.01 lbf.in).
(4)
Make sure that the packings (3) are in position on the adaptor (2). NOTE : If you install the used adaptor (2), put the new packings (3)
____
in position.
(5)
Apply a thin layer of COMMON GREASE (Material No. 04-004) to the shaft of the adaptor (2).
(6)
Install the pressure transducer (4) on the adaptor (2). NOTE : Make sure that the pressure transducer (4) is in the correct
____
position.
(7)
Install the nut (6) and tighten it.
(8)
TORQUE the nut (6) to between 0.3 and 0.9 m.daN (26.54 and 79.64 lbf.in).
(9)
Safety the nut (6) with the new cotter pin (5).
(10) Inflate the tire (Ref. TASK 12-14-32-614-001). Subtask 32-49-15-865-055
B. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 1GV
1EFF : 051-099, 1 32-49-15Page 414 1 1 May 01/05 1 1 1CES 1 Subtask 32-49-15-720-051
C. Functional Test
(1) Do the functional test of the Tire Pressure Indicating System (Ref. TASK 32-49-00-720-001).
5. Close-up
________ Subtask 32-49-15-860-054
A. Put the aircraft back to its initial configuration.
(1)
Lower the aircraft on its wheels. (Ref. TASK 07-12-00-582-001)
(2)
Remove the safety barriers.
(3)
Remove the warning notice(s).
(4)
Make sure that the work area is clean and clear of tool(s) and other items.
1EFF : 051-099, 1 32-49-15Page 415 1 1 May 01/05 1 1 1CES 1
PRESSURE TRANSDUCER - MLG TIRE (12GV,13GV,14GV,15GV) - REMOVAL/INSTALLATION
___________________________________________________________________________ TASK 32-49-16-000-005 Removal of the MLG Tire-Pressure Transducer (12GV,13GV,14GV,15GV)
1.
Reason for the Job
__________________
Self Explanatory
2.
Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific blanking caps No specific circuit breaker(s) safety clip(s) No specific safety barriers No specific warning notice(s) MG174-04 1 DISASSEMBLY TOOL
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
07-12-00-582-002 Jacking for Main Gear Wheel Change 32-49-16-991-004 Fig. 401
3. Job Set-up
__________ Subtask 32-49-16-941-056
A. Safety Precautions
(1)
Put the safety barriers in position.
(2)
In the cockpit, on the panel 400VU put the warning notice(s) in position to tell persons not to operate the landing gear control lever.
(3)
Make sure that the wheel chocks are in position.
1EFF : 051-099, 1 32-49-16Page 401 1 1 May 01/05 1 1 1CES 1 Subtask 32-49-16-865-065
B. Open, safety and tag this(these) circuit breaker(s):
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM LANDING GEAR 起落架8(58)
