(9)
Apply a thin layer of COMMON GREASE (Material No. 04-003) on the
splines (12) and on the splines of the guard assy.
(10) Install the guard assy (22).
NOTE : The debris guard has holes of different diameters :
____
-large diameter (two) : to permits removal of the guard assy without removal of the shroud assy screws (larger than the screw heads)
-medium diameter (two) : to put the locating pins in the correct position. Same holes on the shroud assy (centering function)
-small diameter (four) : to put the four attachment screws in the correct position.
NOTE : Use the locating pin (27) to put the guard assy (22) in the
____
correct position.
NOTE : During the installation, be careful to correctly engage the
____
splines (12).
1EFF : 051-099, 1 32-48-51Page 427 1 1 Aug 01/05R 1 1 1CES 1
NOTE : Make sure that you set the half-bushes (17) and (19) in the
____
correct position.
(11) Install the screws (21) and the washers (20). TORQUE the screws to
0.25 m.daN (22.12 lbf.in). Subtask 32-48-51-865-068
C. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 1GS, 2GS, 3GS, 1GV
Subtask 32-48-51-710-055
D. Operational Test
(1) Do the functional test of the brake fans (Ref. TASK 32-48-00-720-001).
5. Close-up
________ Subtask 32-48-51-942-055
A. Removal of Equipment
(1)
Remove the warning notice(s).
(2)
Make sure that the work area is clean and clear of tool(s) and other items.
(3)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
R 1EFF : 051-099, 1 32-48-51Page 428 1 1 Aug 01/05 1 1 1CES 1R **ON A/C 051-099, 301-399, 401-499,
TASK 32-48-51-000-002
Removal of the Impeller Assy
1.
Reason for the Job
__________________
Self Explanatory
2.
Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------
REFERENCE QTY DESIGNATION
-------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s)
No specific safety barriers
No specific warning notice(s)
MG174-04 1 DISASSEMBLY TOOL
B. Consumable Materials
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
Material No. 11-002 USA MIL-PRF-680
DRY CLEANING SOLVENT (VARSOL/WHITE SPIRIT)
(Ref. 20-31-00)
R 1EFF : 051-099, 301-399, 401-499, 1 32-48-51Page 429 1 1 Aug 01/05 1 1 1CES 1 C. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
**ON A/C 051-099,
32-48-51-991-002-A Fig. 403 R **ON A/C 301-399, 401-499,
32-48-51-991-002 Fig. 403A R **ON A/C 051-099, 301-399, 401-499,
3. Job Set-up
__________
Subtask 32-48-51-941-063
A. Safety Precautions
(1)
Put the safety barriers in position.
(2)
In the cockpit, on the panel 400VU, put warning notice(s) in position to tell persons not to operate the landing gear control lever.
(3) Make sure that the wheel chocks are in position.
Subtask 32-48-51-865-054
B. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM LANDING GEAR 起落架8(44)
