曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

R  (c) Put the other steel plate on the top of the greased steel plate. 
R  (d) Move the aircraft and position the nose wheels on the greased 
R  steel plates (Ref. TASK 09-10-00-584-002). 
R  (4) If the test is to be done with the nose wheels clear of the ground do 
R  this: 
R  (a) Lift the nose gear (Ref. TASK 07-12-00-582-001). 
R  NOTE : Use only a compact axle jack to lift the nose gear.____ 
R  (5) On the nose gear leg, on the electrical box, make sure that the 
R  towing lever is in the normal position (engaged position). 
R  (6) On the panel 400VU, make sure that the landing gear control lever is 
R  in the DOWN position. 

R 1EFF : 401-499, 1 32-51-00Page 542 1 1 Aug 01/05 1 1 1CES 1

R R  (7) On the panel 402VU, make sure that the ANTI SKID NOSE WHEEL switch is in the ON position. 
R R  (8) Do the EIS start procedure (Upper ECAM DU and lower ECAM DU only) (Ref. TASK 31-60-00-860-001). 
R  (9) On the ECAM control panel, push the WHEEL pushbutton switch. 
R R  (10) Make sure that the rudder pedals and the two nose-wheel steering handwheels are in the neutral position. 
R R R  (11) On the overhead panel 23VU: - Make sure that the FLT CTL/ELAC 1 pushbutton switch is pushed (on this pushbutton switch, the OFF and FAULT legends are OFF). 
R R R  (12) On the overhead panel 24VU: - Make sure that the FLT CTL/ELAC 2 pushbutton switch is pushed (on this pushbutton switch, the OFF and FAULT legends are OFF). 
R  **ON A/C ALL
 Subtask 32-51-00-865-099
 B. Make sure that this(these) circuit breaker(s) is(are) closed:
 -------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU FLIGHT CONTROLS/ELAC1/NORM/SPLY 15CE1 B11 49VU FLIGHT CONTROLS/FCDC1/SPLY 20CE1 B10 49VU FLIGHT CONTROLS/SEC1/NORM/SPLY 21CE1 B08 49VU L/G/LGCIU/SYS1/NORM 1GA C09 49VU NAV PROBES/ADIRU 1/AND AOA 1/26VAC 5FP1 F07 49VU NAV PROBES/ADIRU1/115VAC 4FP1 F06
 **ON A/C 001-049, 051-061, 101-105, 201-203,
 121VU ADIRS/ADIRU/3/26VAC AND AOA 121VU ADIRS/ADIRU/3/115VAC  5FP3 4FP3  N08N06
 **ON A/C ALL
 121VU HYDRAULIC/BRAKING AND STEERING/SYS2/SPLY 121VU HYDRAULIC/BRAKING AND STEERING/SYS2/CTL  4GG 3GG  M36M35 

R 1EFF : ALL 1 32-51-00Page 543 1 1 Aug 01/05 1 1 1CES 1

 -------------------------------------------------------------------------------
PANEL DESIGNATION IDENT. LOCATION
 -------------------------------------------------------------------------------121VU HYDRAULIC/BRAKING AND STEERING/SYS1/CTL 1GG M34 121VU HYDRAULIC/BRAKING AND STEERING/SYS1/IND AND/SPLY 2GG M33 121VU HYDRAULIC/LGCIU/SYS2 2GA Q35 121VU HYDRAULIC/LGCIU/SYS1/GRND SPLY 52GA Q34 121VU FLIGHT CONTROLS/FCDC2/SPLY 20CE2 Q20 121VU FLIGHT CONTROLS/SEC3/SPLY 21CE3 Q19 121VU FLIGHT CONTROLS/ELAC2/NORM/SPLY 15CE2 R20
R **ON A/C 062-099, 106-149, 151-199, 204-299, 301-399, 401-499,
 121VU ADIRS/ADIRU/3/26VAC AND AOA 5FP3 N07
 121VU ADIRS/ADIRU/3/115VAC 4FP3 N05
 **ON A/C ALL
 Subtask 32-51-00-865-100
 C. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged
 -------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------121VU ENGINE/ENG2/OIL/PRESS 2EN2 N42 121VU ENGINE/ENG1/OIL/PRESS 2EN1 N40
 4. Procedure
_________
 Subtask 32-51-00-720-059
 A. Do the test of the Nose Wheel Steering with the handwheel (Ref. TASK 32-51-00-720-003)
 NOTE : Do this test with the CAPT handwheel, then with the FO handwheel.
____
 1EFF : ALL 1 32-51-00Page 544 1 1 Aug 01/05 1 1 1CES 1 Subtask 32-51-00-710-053

 B. Test of the Nose Wheel Steering with the pedals
 -------------------------------------------------------------------------------ACTION RESULT -------------------------------------------------------------------------------
1. On the overhead panel 24VU:
-release the FLT CTL/ELAC 2 pushbutton switch.
2. On the panel 121VU:
- open the circuit breakers 3GG and 4GG
 -make sure that the circuit breakers 1GG and 2GG are closed
 3.
 Push the Captain or First Officer left rudder-pedal fully forward

4.
 Release the rudder pedal to the neutral posiion

5.
 Push the Captain or First Officer right rudder-pedal fully forward

6.
 Release the rudder pedal to the neutral posiion
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM LANDING GEAR 起落架8(89)