(2)
 Make sure that the work area is clean and clear of tool(s) and other items.

 (3)
 Remove the ground support and maintenance equipment, the special and standard tools and all other items.

R 1EFF : 301-399, 401-499, 1 32-48-51Page 414 1 1 Aug 01/05 1 1 1CES 1

 **ON A/C 051-099,

 TASK 32-48-51-000-005-A
 Removal of the Fan Assy (7GS,8GS,9GS,10GS)

 1.
 Reason for the Job

__________________
 Self Explanatory

 2.
 Job Set-up Information

______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific blanking caps No specific circuit breaker(s) safety clip(s) No specific safety barriers No specific warning notice MG174-04 1 DISASSEMBLY TOOL
 B. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
32-48-51-991-006 Fig. 402
 3. Job Set-up
__________ Subtask 32-48-51-941-056
 A. Safety Precautions
 (1)
 Put the safety barriers in position.

 (2)
 In the cockpit, on the panel 400VU put a warning notice in position to tell persons not to operate the landing gear control lever.

 (3)
 Make sure that the wheel chocks are in posistion.

 1EFF : 051-099, 1 32-48-51Page 415 1 1 Aug 01/05R 1 1 1CES 1

 Subtask 32-48-51-865-066
 B. Open, safety and tag this(these) circuit breaker(s):
 -------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------
121VU HYDRAULIC/BRK FAN/WHEELS/3 AND 4 2GS L35 121VU HYDRAULIC/BRK FAN/WHEELS/1 AND 2 1GS L32 121VU HYDRAULIC/BRK/FAN/CTL 3GS M32 121VU HYDRAULIC/TIRE/PRESS 1GV M31
 4. Procedure
_________
 (Ref. Fig. 402/TASK 32-48-51-991-006) Subtask 32-48-51-020-055
 A. Removal of the Fan Assy
 (1)
 Remove the screws (21) and the washers (20).

 (2)
 Remove the guard assy (22). NOTE : Remove the guard assy (22) along the centerline of the axle so

____ that you do not cause damage to the splines (12).

 (3)
 Remove the impeller (24)
 Pre SIL 32 - 095

 -Cut and remove the lockwire and discard it, then hold the impeller
 (24) with DISASSEMBLY TOOL (MG174-04) and loosen the nut (23). Pull axially on the impeller.
 -Remove the impeller (24).
 Post SIL 32 - 095

 -Cut and remove the lockwire and discard it
 -Hold the impeller (24) with DISASSEMBLY TOOL (MG174-04), remove the nut (23) and the washer (51).
 -Pull axially on the impeller (24) and remove it.

 (4)
 Disconnect the electrical connector (29) from the plug (11) and put the blanking caps in position.

 1EFF : 051-099, 1 32-48-51Page 416 1 1 Aug 01/05R 1 1 1CES 1

 INTENTIONALLY BLANK

R 1 1
32-48-51Page 417
1 1 Aug 01/05 1 1 1CES 1

 Fan Assy Figure 402/TASK 32-48-51-991-006- 12 (SHEET 1)
 1EFF : 051-099, 1 32-48-51Page 418
1 1 Aug 01/05R 1 1
1CES 1

 Fan Assy Figure 402/TASK 32-48-51-991-006- 22 (SHEET 2)
 1EFF : 051-099, 1 32-48-51Page 419
1 1 Aug 01/05R 1 1
1CES 1

 (5)
 Attach the connector (29) and the cable (38) to the wheel with a
 cord.

 (6)
 Remove the screws (18).

 (7)
 Remove the shroud (25).

 (8)
 Loosen the screw (28) and remove the collar (15).

 (9)
 Remove the joint (16).

 (10)
 Remove the cotter pins (30) and discard them. Remove the nuts (31), the washers (32) and the bolts (14).

 (11)
 Remove the mounting fixture assy (10). NOTE : When you remove the mounting fixture assy (10), do not cause

____
 damage to the electrical cables.

 NOTE : Do not apply pressure against the rotating components of the
____
 pressure transducer (13).

 (12)
 Disconnect the connector (33) from the pressure transducer connector

 (36) and put the blanking cap in position.

 (13)
 Cut and remove the lockwire and discard it, then remove the nut (34).
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM LANDING GEAR 起落架8(41)