R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 32-46-00Page 303 1201-299, 301-399, 1Aug 01/05 1 1 1CES 1
CFDIU MENU - PIN PROGRAMMING SELECTION R Figure 301/TASK 32-46-00-991-001-A
R 1EFF : 001-049, 051-099, 101-105, 151-199, 1 32-46-00Page 304 1201-220, 301-399, 1Aug 01/05 1 1 1CES 1
-------------------------------------------------------------------------------ACTION RESULT -------------------------------------------------------------------------------
1.
On the MCDU, push the line key adjacent to the BSCU A indication.
2.
Push the line key adjacent to the PIN-PROG SELECTION indication.
3.
Push the line key adjacent to the A/C pin programming of the BSCU in relation to the type of brakes and tires related to the A/C pin programming.
NOTE : The types of brakes and
____ tires on the A319 are the same as those on the A320.
4.
On the panel 402VU, set the A/SKID & NOSE WHEEL switch 5GG to OFF then to ON.
5.
Push the line key adjacent to the RETURN indication to get the SYSTEM REPORT/TEST L/G page.
6.
Push the line key adjacent to the BSCU B indication.
7.
Do the same actions as in Para.
2. 3. and 4.
-
the BSCU SYS 1 page comes into view.
-
the BSCU SYS 1 PIN-PROG SELECTIONpage comes into view.
-
the BSCU SYS 1 PIN PROGRAMMINGMESSAGE page comes into view andgives instructions.
NOTE : Make sure that the PIN-PROG
____ SELECT ACCEPTED indication comesinto view.If the CAUTION indication comesinto view, push the line key adjacent to the RETURN indication and do again the step
3.
If the CAUTION indication comes
into view again, do a check of
the A/C pin programming (Ref.
ASM 32-42/02).
-same results as for the BSCU SYS 1.
R 1EFF : 001-049, 051-099, 101-105, 151-199, 1 32-46-00Page 305 1201-220, 301-399, 1Aug 01/05 1 1 1CES 1 **ON A/C 106-149, 221-299,
Subtask 32-46-00-970-050-B
A. Selection of the BSCU Pin-Programming
(Ref. Fig. 301A/TASK 32-46-00-991-001-B)
(1) Do a visual check of the brakes and main tires and note the informations (tire size, brake manufacturer) if you could not get these data from a previous BSCU installation (LRU IDENTIFICATION page).
NOTE : In case of doubt, always refer to the latest certified wheel
____ and brake configuration applicable to the aircraft.
NOTE : The PIN-PROG SELECTION page may be different according to the
____ BSCU standard (some selections may not be found). You will find below some information to understand all the selections.
NOTE : Unless specified on the MCDU page, A320 means A319/A320
____
-MBFG: (MESSIER BUGATTI or GOODRICH for A319/A320-MESSIER/GOODRICH FOR A321)
-ABS: (AIRCRAFT BRAKING SYSTEM)
-ANA: (or MBFG-ANA): Same as MBFG with a specific AUTO BRAKE LO mode setting
-BFG-ANA : Same as BFG with a specific AUTO BRAKE LO mode setting
-BFG: GOODRICH
-ALS-c: HONEYWELL
-ALS-S: HONEYWELL
NOTE : The selections BFG/BFG-ANA/ALS-S are only provisions. No
____ aircraft pin programming corresponds to these selections. The selection A320-ABS (or A319/A320 ABS) is no longer used.
NOTE : You must do the pin programming selection on the two systems:
____
BSCU SYS1 an BSCU SYS2.
R 1EFF : 106-149, 221-299, 1 32-46-00Page 306 1 1 Aug 01/05 1 1 1CES 1
CFDIU MENU - PIN PROGRAMMING SELECTION
Figure 301A/TASK 32-46-00-991-001-B
R 1EFF : 106-149, 221-299, 1 32-46-00Page 307 1 1 Aug 01/05 1 1 1CES 1
-------------------------------------------------------------------------------ACTION RESULT -------------------------------------------------------------------------------
1.
On the MCDU, push the line key adjacent to the BSCU 1 indication.
2.
Push the line key adjacent to the PIN-PROG SELECTION indication.
3.
Push the line key adjacent to the A/C pin programming of the BSCU in relation to the type of brakes and tires related to the A/C pin programming.
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM LANDING GEAR 起落架8(15)
