(2)
Put a warning notice(s) in the cockpit to tell persons not to operate the slat controls.
Subtask 27-84-62-010-050
B. Get Access
(1)
Put the adjustable access platform below the applicable zone 510 or
610.
(2)
Remove the applicable closing plate(s) (Ref. TASK 27-84-69-000-001).
(3)
Remove the applicable slat:
-
for the tracks 5 and 6 (Ref. TASK 27-84-64-000-001)
-
for the tracks 7 and 8 (Ref. TASK 27-84-65-000-001)
-
for the tracks 9 and 10 (Ref. TASK 27-84-66-000-001)
-
for the tracks 11 and 12 (Ref. TASK 27-84-67-000-001).
(4) Remove the applicable actuators: - for the tracks 5, 6, 8, 10 and 12 (Ref. TASK 27-84-49-000-001) - for the tracks 7, 9, and 11 (Ref. TASK 27-84-49-000-002).
(5) Make sure that the TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER (98D27803500001) is on the slat/flap control lever.
Subtask 27-84-62-865-053
C. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU FLIGHT CONTROLS/SLT/CTL AND MONG/SYS1 5CV B06 121VU FLIGHT CONTROLS/SLT/CTL/SYS2 7CV R21
4. Procedure_________
(Ref. Fig. 401/TASK 27-84-62-991-001)
Subtask 27-84-62-020-053
R A. Removal of the Slat Tracks 5 thru 12
R R R (1) Install the applicable TOOL-BACKSTOP SLAT (1) through the guide (4) on the side of the track (2). Install the backstop tool on the inboard side on the LH wing and on the outboard side on the RH wing: - for the tracks 5 thru 8 install the TOOL-BACKSTOP SLAT (TRACKS 5, 6, 7, AND 8) (98D27804015000) - for the tracks 9 thru 12 install the TOOL-BACKSTOP SLAT (TRACKS 9, 10, 11, AND 12) (98D27804016000).
(2) Push the applicable slat backstop tool (1) against the rearstop (3) to disengage it from the track stop. Pull the track (2) from its installed position and remove it.
(3) Remove the applicable TOOL-BACKSTOP SLAT (1) from the track (2).
Slat Tracks 5 thru 12 - Location and Detail
Figure 401/TASK 27-84-62-991-001
1EFF : ALL 1 27-84-62 Page 404
1 1 Feb 01/98
1 1
1CES 1
TASK 27-84-62-400-001
Installation of the Slat Tracks 5 thru 12
WARNING : MAKE SURE THAT THE FLIGHT CONTROL SAFETY-LOCKS AND THE WARNING
_______
NOTICES ARE IN POSITION.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
GEAR.
1. Reason for the Job
__________________
R R Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific safety barriers
No specific warning notice(s)
No specific adjustable access platform 3.5 m (11 ft. 6 in.)
98D27804015000 1 TOOL-BACKSTOP SLAT (TRACKS 5, 6, 7, AND 8)
98D27804016000 1 TOOL-BACKSTOP SLAT (TRACKS 9, 10, 11, AND 12)
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 04-024 AIB AIMS 09-06-001
SYNTHETIC GREASE FOR FLAP & SLAT MECHANISM
(Ref. 20-31-00)
Material No. 09-018 USA AMS 3267/3 中國航空網(wǎng) m.k6050.com 航空翻譯 www.aviation.cn 本文鏈接地址：A320飛機(jī)維護(hù)手冊 AMM FLIGHT CONTROLS 飛行操縱8(79)
