R No specific Torque Wrench : range 0.00 to 1.20 m.daN R (0.00 to 9.00 lbf.ft) No specific Torque Wrench : range 0.20 to 3.60 m.daN
(2.00 to 26.00 lbf.ft) No specific Torque Wrench : range 1.00 to 10.00 m.daN
(8.00 to 75.00 lbf.ft) 98D27504030001 2 LOCK-TORQUE SHAFT (FLAPS AND SLATS) WITH CLAMP-PIVOT 98D27803000000 1 LOCKING TOOL - FLAP/SLAT CONTROL LEVER B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
R Material No. 02-003 F NSA 307110 TYPE 4 HYDRAULIC FLUID (PHOSPHATE ESTER BASE) (Ref. 20-31-00)
Material No. 04-018
GENERAL PURPOSE ASSEMBLY PASTE (Ref. 20-31-00)
Material No. 05-005 USA MIL-C-16173 GRADE II
CORROSION PREVENTIVE (Ref. 20-31-00)
Material No. 09-013 USA MIL-PRF-81733 TYPE I CLASS A
CORROSION INHIBITING BRUSH CONSISTENCY
(Ref. 20-31-00)
Material No. 11-002 USA MIL-PRF-680
DRY CLEANING SOLVENT (VARSOL/WHITE SPIRIT)
(Ref. 20-31-00)
Material No. 16-003 F ASNB70720
COATING (OBSOLETE USE 16-021) (Ref. 20-31-00)
Material No. 19-010 USA AMS 5687
LOCKWIRE STAINLESS STEEL ANNEALED 0.8MM DIA
(Ref. 20-31-00)
C. Expendable Parts
-------------------------------------------------------------------------------FIG.ITEM |DESIGNATION |IPC-CSN -------------------------------------------------------------------------------
cotter pin 27-84-03 06 -100
D. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
12-12-29-611-001 Fill the Hydraulic Fluid Reservoir with a Hand Pump 12-12-29-611-002 Fill the Hydraulic Fluid Reservoir with a Hydraulic Service Cart
20-28-00-912-004 Electrical Bonding of Components With Conductive Bolts and Screws and Bonding Straps in the Fuselage and in the Wings (this does not include the tanks)-
27-00-00-080-002 Removal of the Flap/Slat Control-Lever Locking Tool (98D27803000000)
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
27-00-00-480-002 Installation of the Flap/Slat Control-Lever Locking Tool (98D27803000000) 27-50-00-000-003 Removal of the Lock-Torque Shaft - Flaps and Slats (98D27504030001) 27-50-00-400-003 Installation of the Lock-Torque Shaft - Flaps and Slats (98D27504030001) 27-80-00-866-005 Retracting the Slats on the Ground
R 27-81-00-820-001 Manual Adjustment of the Position Pick-Off Units 27-84-00-710-001 Operational Test of the Slat System 29-00-00-864-001 Put the Related Hydraulic System in the Depressurized Configuration before Maintenance Action 29-10-00-863-001 Pressurize the Green Hydraulic System 29-10-00-863-003 Pressurize the Blue Hydraulic System with a Ground Power Supply 29-14-00-614-001 Depressurization of the Hydraulic Reservoirs 29-14-00-614-002 Pressurization of the Hydraulic Reservoirs through the Ground Connector
R 31-32-00-860-006 Procedure to Get Access to the SYSTEM REPORT/TEST
R F/CTL Page 32-12-00-410-001 Close the Main Gear Doors after Access 27-84-51-991-001 Fig. 401 27-84-51-991-002 Fig. 402
3. Job Set-up
__________
Subtask 27-84-51-860-052
A. Aircraft Maintenance Configuration
(1)
Make sure that the slats are in the 0 degree position (Ref. TASK 27-80-00-866-005).
(2)
Make sure that the LOCKING TOOL - FLAP/SLAT CONTROL LEVER (98D27803000000) is installed (Ref. TASK 27-00-00-480-002) on the slat/flap control lever.
(3)
Make sure that the access platform is in position at the opening of the main door of the main gear.
(4)
Make sure that the Green and the Blue hydraulic systems are depressurized and put them in the maintenance configuration (Ref. TASK 29-00-00-864-001).
(5)
Make sure that the reservoirs of the Green and the Blue hydraulic systems are depressurized (Ref. TASK 29-14-00-614-001).
(6)
Make sure that the warning notice in position to tell persons not to pressurize the hydraulic systems.
(7)
Make sure that the LOCK-TORQUE SHAFT (FLAPS AND SLATS) WITH CLAMP-PIVOT (98D27504030001) is installed to lock the left slat transmission (Ref. TASK 27-50-00-400-003).
(8)
Make sure that the LOCK-TORQUE SHAFT (FLAPS AND SLATS) WITH CLAMP-PIVOT (98D27504030001) is installed to lock the right slat transmission (Ref. TASK 27-50-00-400-003).
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FLIGHT CONTROLS 飛行操縱8(35)
