R No specific Torque Wrench : range 0.00 to 1.20 m.daN R (0.00 to 9.00 lbf.ft) 98D27803000000 1 LOCKING TOOL - FLAP/SLAT CONTROL LEVER
B. Consumable Materials
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
R Material No. 02-003 F NSA 307110 TYPE 4 HYDRAULIC FLUID (PHOSPHATE ESTER BASE) (Ref. 20-31-00)
C. Expendable Parts
-------------------------------------------------------------------------------
FIG.ITEM |DESIGNATION |IPC-CSN
-------------------------------------------------------------------------------
6 back-up ring 27-84-53 01 -130 7 back-up ring 27-84-53 01 -120 9 O-ring 27-84-53 01 -110 10 O-ring 27-84-53 01 -100 15 O-ring 27-84-53 01 -150 16 O-ring 27-84-53 01 -140
D. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
12-12-29-611-001 Fill the Hydraulic Fluid Reservoir with a Hand Pump 12-12-29-611-002 Fill the Hydraulic Fluid Reservoir with a Hydraulic Service Cart 27-00-00-080-002 Removal of the Flap/Slat Control-Lever Locking Tool (98D27803000000) 27-00-00-480-002 Installation of the Flap/Slat Control-Lever Locking
Tool (98D27803000000) 27-80-00-866-005 Retracting the Slats on the Ground 27-84-00-710-001 Operational Test of the Slat System 29-00-00-864-001 Put the Related Hydraulic System in the Depressurized
Configuration before Maintenance Action 29-14-00-614-001 Depressurization of the Hydraulic Reservoirs 29-14-00-614-002 Pressurization of the Hydraulic Reservoirs through
the Ground Connector
32-12-00-410-001 Close the Main Gear Doors after Access
27-84-53-991-002 Fig. 402
3. Job Set-up
__________
Subtask 27-84-53-860-057
A. Aircraft Maintenance Configuration
(1)
Make sure that the slats are in the 0 degree position (Ref. TASK 27-80-00-866-005).
(2)
Make sure that the LOCKING TOOL - FLAP/SLAT CONTROL LEVER (98D27803000000) is installed (Ref. TASK 27-00-00-480-002) on the slat/flap control lever.
(3)
Make sure that the access platform is in position at the opening of the main door of the main gear.
(4)
Make sure that the Green and the Blue hydraulic systems are depressurized and put them in the maintenance configuration (Ref. TASK 29-00-00-864-001).
(5)
Make sure that the reservoirs of the Green and the Blue hydraulic systems are depressurized (Ref. TASK 29-14-00-614-001).
(6)
Make sure that the warning notice in position to tell persons not to pressurize the hydraulic systems.
(7)
Make sure that a container is in position below the Power Control Unit (PCU) (1).
Subtask 27-84-53-865-054
B. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU FLIGHT CONTROLS/SLT/CTL AND MONG/SYS1 5CV B06 121VU FLIGHT CONTROLS/SLT/CTL/SYS2 7CV R21
4. Procedure
_________
(Ref. Fig. 402/TASK 27-84-53-991-002) Subtask 27-84-53-420-051
A. Installation of the Solenoid Valve.
(1)
Clean the component interface and/or the adjacent area.
(2)
Do an inspection of the component interface and/or the adjacent area.
(3)
Apply HYDRAULIC FLUIDS (Material No. 02-003) to the new back-up ring (6), the new back-up ring (7) and the new O-ring (9).
(4)
Install the new back-up rings (6),(7) and the new O-rings (9).
(5)
Install the new O-ring (10), the new O-ring (15) and the new O-ring
(16) on the solenoid valve (1).
(6)
Carefully install the solenoid valve (1) to the valve block (12).
(7)
Install the washers (5) and the bolts (4).
(8)
TORQUE the bolts (4) to between 0.25 and 0.27 m.daN (22.12 and 23.89 lbf.in).
Subtask 27-84-53-860-059
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FLIGHT CONTROLS 飛行操縱8(48)
