(d)
Do not torque or safety the nut (19).
(3) At the No. 2 slat track:
(a) Attach the slat to the slat tracks and the slat tracks links with:
-
the bolts (15) and (16)
-
the washers (2) and (6)
-
the nuts (3) and (5).
NOTE : If necessary, turn the eccentric bushes (9) to help
____
install the bolts (15) and (16).
(b)
TORQUE the nuts (3), (5), (17) and (19) to between 4.2 and 4.8 m.daN (30.97 and 35.39 lbf.ft).
(c)
Safety the nuts (3), (5), (17) and (19) with the new cotter pins (5). (Ref. Fig. 405/TASK 27-84-63-991-004)
(d)
Do not torque or safety the nut (18).
(4) At the No. 3 and 4 slat tracks:
CAUTION : MAKE SURE THAT THE APPLICABLE TYPE OF SLAT TRACK LINKS IS
_______ INSTALLED (ON TRACKS 1 AND 2) WHEN YOU REPLACE THE SLAT.
R 1EFF : 062-099, 106-149, 151-199, 204-299, 1 27-84-63Page 424 1301-399, 401-499, 1Aug 01/05 1 1 1CES 1
(a) Install the bush (34) and attach the slat to the slat tracks and the slat tracks links with:
-
the bolts (39) and (41)
-
the washers (30) and (33)
-
the nuts (31) and (32).
NOTE : If necessary, turn the eccentric bushes (36) to help
____ install the bolts (39) and (41).
(b)
TORQUE the nuts (31) and (32) to between 6.6 and 7.6 m.daN (48.67 and 56.04 lbf.ft).
(c)
Safety the nuts (31) and (32) with the new cotter pins (5). (Ref. Fig. 405/TASK 27-84-63-991-004)
(d)
Do not torque or safety the nut (42).
(5)
Remove the SLING-SLATS (Ref. TASK 27-80-00-000-001).
(6)
You must adjust the upper trailing-edge of the slat to its maximum height, related to the fixed leading-edge. To adjust the height, turn the eccentric bushes (9) and (36) at the No. 1, 2, 3 and 4 slat tracks.
**ON A/C 001-049, 052-061, 101-105, 201-203,
Subtask 27-84-63-820-055
C. Adjustment of the Slat (Ref. Fig. 401/TASK 27-84-63-991-001, 402/TASK 27-84-63-991-002, 403/TASK 27-84-63-991-003, 405/TASK 27-84-63-991-004)
(1)
Install the BLOCK-SLAT GAPPING (98D27804020000) at the No. 9 slat track.
(2)
Remove the LOCK-TORQUE SHAFT (FLAPS AND SLATS) WITH CLAMP-PIVOT, installed outboard of the removed torque shaft FIN 6010CM(6060CM) (Ref. TASK 27-50-00-000-003).
(3)
Use the ADAPTOR-DRIVE, SLAT (AND FLAP) to retract the slats until they are approximately 50.8 mm (2.0000 in.) +/- 6.35 mm (0.2500 in.) from the BLOCK-SLAT GAPPING.
(4)
Use the BAR-TURNING (98D27804011000) to slowly retract the slats until the BLOCK-SLAT GAPPING touches the bottom roller at the No. 9 slat track.
R 1EFF : 001-049, 052-099, 101-149, 151-199, 1 27-84-63Page 425 1201-299, 301-399, 401-499, 1Aug 01/05 1 1 1CES 1
(5)
Install the LOCK-TORQUE SHAFT (FLAPS AND SLATS) WITH CLAMP-PIVOT outboard of the removed torque shaft FIN 6010CM(6060CM) (Ref. TASK 27-50-00-400-003).
(6)
Adjust the eccentric bushes (10) and (36) at the Nos. 1, 2, 3 and 4 slat tracks to get dimension J. Refer to the table that follows.
NOTE : Measure dimension J above the applicable slat track.
____ -------------------------------------------------------------------------------
| TRACK | DIMENSION J | MAXIMUM ADJUSTMENT BECAUSE OF |
| -- NO. ------ | --- --------------------- | ------- LOCKING PLATE INSTALLATION ----------------------------------- |-----
| 1 | 4.75 mm (0.187 in.) | + 0.25 mm (0.01 in.) - 0.25 mm (0.01 in.) |
| 2 | 5.00 mm (0.196 in.) | + 0.25 mm (0.01 in.) - 0.25 mm (0.01 in.) |
| 3 | 6.50 mm (0.255 in.) | + 0.25 mm (0.01 in.) - 0.25 mm (0.01 in.) |
| 4 | 7.00 mm (0.275 in.) | + 0.25 mm (0.01 in.) - 0.25 mm (0.01 in.) |
-------------------------------------------------------------------------------
(7)
Install the locking plates (13) and (38) and the nuts (14) and (40).
(8)
TORQUE the nuts (19) and (42) to between 4.2 and 4.8 m.daN (30.97 and
35.39 lbf.ft).
(9)
Safety the nuts (19) and (42) with the new cotter pins (5).
(10)
Remove the LOCK-TORQUE SHAFT (FLAPS AND SLATS) WITH CLAMP-PIVOT, installed outboard of the removed torque shaft FIN 6010CM(6060CM) (Ref. TASK 27-50-00-000-003).
(11)
Use the pneumatic wrench and the ADAPTOR-DRIVE, SLAT (AND FLAP) to fully extend the slats.
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FLIGHT CONTROLS 飛行操縱8(119)
