-------------------------------------------------------------------------------
(b)
Install the locking plates (13) and (38) and the nuts (14) and (40).
(c)
TORQUE the nuts (19) and (42) to between 4.2 and 4.8 m.daN (30.97 and 35.39 lbf.ft).
(d)
Safety the nuts (19) and (42) with the new cotter pins (5).
(e)
Remove the LOCK-TORQUE SHAFT (FLAPS AND SLATS) WITH CLAMP-PIVOT, installed outboard of the removed torque shaft FIN 6010CM(6060CM) (Ref. TASK 27-50-00-000-003).
(f)
Use the pneumatic wrench and the ADAPTOR-DRIVE, SLAT (AND FLAP) to fully extend the slats.
(g)
Install the LOCK-TORQUE SHAFT (FLAPS AND SLATS) WITH CLAMP-PIVOT outboard of the removed torque shaft FIN 6010CM(6060CM) (Ref. TASK 27-50-00-400-003).
(h)
Apply special materials:
WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER
_______ SPECIAL MATERIALS ONLY WITH A GOOD SUPPLY OF AIR. OBEY THE MANUFACTURERS INSTRUCTIONS. PUT ON PROTECTIVE CLOTHING. DO NOT GET THEM IN YOUR MOUTH. DO NOT SMOKE. DO NOT BREATHE THE GAS. THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN IRRITANT. GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED.
R 1EFF : 062-099, 106-149, 151-199, 204-299, 1 27-84-63Page 431 1301-399, 401-499, 1Aug 01/05 1 1 1CES 1
1_ Apply SEALANTS (Material No. 09-001) to:
- the nuts (4), (6), (18), (19), (20), (31), (32) and (42)
- the bolt heads (11), (12), (15), (16), (17), (37), (39) and
(41)
- the locking plates (13) and (38).
(i)
Remove the BLOCK-SLAT GAPPING from the No. 9 slat track.
(j)
Do a check of the slat lower trailing-edge, dimension L: 1 Remove the LOCK-TORQUE SHAFT (FLAPS AND SLATS) WITH CLAMP-
_ PIVOT, installed outboard of the removed torque shaft FIN 6010CM(6060CM) (Ref. TASK 27-50-00-000-003).
2 Use the pneumatic wrench and the ADAPTOR-DRIVE, SLAT (AND
_ FLAP) to fully retract the slats.
3 Install the LOCK-TORQUE SHAFT (FLAPS AND SLATS) WITH CLAMP-
_ PIVOT outboard of the removed torque shaft FIN 6010CM(6060CM) (Ref. TASK 27-50-00-400-003).
4 Measure the dimension L of the slat lower trailing-edge. The
_ dimension L must be 5 mm (0.1968 in.) +/- 2 mm (0.0787 in.) at all points along the length of the slat. (Ref. Fig. 405/TASK 27-84-63-991-004)
5 The slat lower trailing-edge must not be more than 1 mm
_ (0.0393 in.) into-wind or out-of-wind.
NOTE : The dimension L and the into-wind and out-of-wind
____ dimensions are not adjustable. If the dimensions you measure are out of limits, you must tell the design authority at Airbus Industrie.
(k) Install and adjust the closing plates (9) and (35) (Ref. TASK 27-84-69-400-001).
(7) At the No. 2 slat track:
(a) Adjust the eccentric bush (9) to get dimension J. Refer to the table that follows.
NOTE : Measure dimension J above the applicable slat track.
____
R 1EFF : 062-099, 106-149, 151-199, 204-299, 1 27-84-63Page 432 1301-399, 401-499, 1Aug 01/05 1 1 1CES 1
-------------------------------------------------------------------------------
| TRACK | DIMENSION J | MAXIMUM ADJUSTMENT BECAUSE OF |
| -- NO. ------ | --- --------------------- | ------ LOCKING PLATE INSTALLATION ----------------------------------- |------
| 2 | 5.00 mm (0.196 in.) | + 0.25 mm (0.01 in.) - 0.25 mm (0.01 in.) |
-------------------------------------------------------------------------------
(b)
Install the locking plate (12) and the nut (13).
(c)
TORQUE the nut (18) to between 4.2 and 4.8 m.daN (30.97 and 35.39 lbf.ft).
(d)
Safety the nut (18) with the new cotter pin (5).
(e)
Remove the LOCK-TORQUE SHAFT (FLAPS AND SLATS) WITH CLAMP-PIVOT, installed outboard of the removed torque shaft FIN 6010CM(6060CM) (Ref. TASK 27-50-00-000-003).
(f)
Use the pneumatic wrench and the ADAPTOR-DRIVE, SLAT (AND FLAP) to fully extend the slats.
(g)
Install the LOCK-TORQUE SHAFT (FLAPS AND SLATS) WITH CLAMP-PIVOT outboard of the removed torque shaft FIN 6010CM(6060CM) (Ref. TASK 27-50-00-400-003).
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FLIGHT CONTROLS 飛行操縱8(122)
