-
for the right wing, install the panels 621AB, 621BB, 621CB, 621EB.
(4) Install the applicable closing plate(s) (Ref. TASK 27-84-69-400-001). Subtask 27-84-61-942-056
B. Removal of Equipment
(1)
Remove the safety barriers.
(2)
Remove the warning notice(s).
(3)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
1EFF : ALL 1 27-84-61Page 428 1 1 May 01/04R 1 1 1CES 1
TASK 27-84-61-000-002 Removal of the Side-Rollers - Slat Tracks 1 thru 4 WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE. WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
GEAR.
1.
Reason for the Job
__________________
Self Explanatory
2.
Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s)
No specific safety barriers
No specific warning notice
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
27-84-48-000-001 Removal of the Type A Actuators
6013CM(6063CM)/6015CM(6065CM)
27-84-61-000-001 Removal of the Slat Tracks 1 thru 4
27-84-63-000-001 Removal of the No. 1 Slat
R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
27-84-61-991-003-A Fig. 402
-------------------------------------------------------------------------------
REFERENCE DESIGNATION -------------------------------------------------------------------------------
**ON A/C 301-399,
27-84-61-991-003 Fig. 402A
**ON A/C ALL
27-84-61-991-004 Fig. 403
__________
3. Job Set-up
R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
(Ref. Fig. 402/TASK 27-84-61-991-003-A)
**ON A/C 301-399,
(Ref. Fig. 402A/TASK 27-84-61-991-003)
**ON A/C ALL
(Ref. Fig. 403/TASK 27-84-61-991-004)
Subtask 27-84-61-941-056
A. Safety Precautions
(1)
Put the safety barriers in position.
(2)
Put the warning notice in the cockpit to tell persons not to operate the slat controls.
Subtask 27-84-61-860-051
B. Aircraft Maintenance Configuration
(1) Make sure that the TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER is on the flap and slat control lever on panel 114VU.
Subtask 27-84-61-865-061
C. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU FLIGHT CONTROLS/SLT/CTL AND MONG/SYS1 5CV B06 121VU FLIGHT CONTROLS/WTB/SLT/SYS2 11CV P19 121VU FLIGHT CONTROLS/SLT/CTL/SYS2 7CV R21 122VU FLIGHT CONTROLS/WTB/SLT/SYS1 9CV S06
Subtask 27-84-61-010-053
D. Get Access
(1)
Remove the Slat 1 (Ref. TASK 27-84-63-000-001).
(2)
Remove the applicable access panels:
-
for the left wing, remove the panels 521AB, 521BB, 521CB, 521EB
-
for the right wing, remove the panels 621AB, 621BB, 621CB, 621EB.
(3)
For the tracks 2 and 3, remove the applicable actuators (Ref. TASK 27-84-48-000-001).
(4)
When it is necessary to remove all the side-rollers (25), remove the applicable track (2) (Ref. TASK 27-84-61-000-001).
NOTE : To replace two or more side-rollers from opposite sides of the
____ track, you must remove all of the side-rollers. Keep the serviceable side-rollers and their related shims together for the installation. To replace side-rollers at the same side of the track, remove only the side-rollers you are to replace.
4. Procedure
_________
R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FLIGHT CONTROLS 飛行操縱8(67)
