(2)
Remove the safety barriers.
(3)
Remove the access platform(s).
(4)
Remove the warning notice(s).
(5)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
1EFF : ALL 1 27-84-68Page 416 1 1 Aug 01/05R 1 1 1CES 1
CLOSING PLATES - SLAT TRACKS - REMOVAL/INSTALLATION
___________________________________________________
TASK 27-84-69-000-001
Removal of the Closing Plates for the Slat Tracks 1 thru 12
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific pneumatic wrench No specific safety barriers No specific warning notice No specific adjustable access platform 4 m (13 ft. 1 in.) 98D27803500001 1 TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER 98D27804001000 1 ADAPTOR-DRIVE, SLAT (AND FLAP)
1EFF : ALL 1 27-84-69Page 401 1 1 Feb 01/01R 1 1 1CES 1
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
27-50-00-400-003 Installation of the Lock-Torque Shaft - Flaps and
Slats (98D27504030001)
27-80-00-866-005 Retracting the Slats on the Ground
27-84-45-000-004 Removal of the Torque Shaft 6010CM(6060CM)
27-84-69-991-003 Fig. 401
**ON A/C 001-049, 051-061, 101-105, 201-203,
27-84-69-991-001 Fig. 402 R **ON A/C 062-099, 106-149, 151-199, 204-299, 301-399, 401-499,
27-84-69-991-001-A Fig. 402A
**ON A/C ALL
3. Job set-up
__________
Subtask 27-84-69-941-052
A. Safety Precautions
(1)
Put safety barriers in position.
(2)
Put a warning notice in the cockpit to tell persons not to operate the slat controls.
Subtask 27-84-69-860-050
B. Aircraft Maintenance Configuration
(1)
Retract the slats fully (Ref. TASK 27-80-00-866-005).
(2)
Install the TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER (98D27803500001) on the flap/slat control lever.
Subtask 27-84-69-010-050
C. Get Access
(1)
Remove the applicable torque shaft (Ref. TASK 27-84-45-000-004):
-
for the left wing, remove (FIN 6010CM)
-
for the right wing, remove (FIN 6060CM).
(2)
Make sure that the LOCK-TORQUE SHAFT (FLAPS AND SLATS) WITH CLAMP-PIVOT (98D27504030001) is installed on the applicable torque shaft (Ref. TASK 27-50-00-400-003).
(3)
Put an adjustable access platform at the applicable slat track.
(4)
Install the ADAPTOR-DRIVE, SLAT (AND FLAP) (98D27804001000) and a pneumatic wrench on the applicable gearbox : (Ref. Fig. 401/TASK 27-84-69-991-003)
-
for the left wing, use (FIN 6011CM)
-
for the right wing, use (FIN 6061CM).
(5)
Use the pneumatic wrench to slowly extend the slats.
4. Procedure
_________
**ON A/C 001-049, 051-061, 101-105, 201-203,
(Ref. Fig. 402/TASK 27-84-69-991-001) R **ON A/C 062-099, 106-149, 151-199, 204-299, 301-399, 401-499,
(Ref. Fig. 402A/TASK 27-84-69-991-001-A)
**ON A/C ALL
Subtask 27-84-69-020-050
A. Removal of the Closing Plates for the Slat Tracks 1 thru 12
(1) Remove the screws (4), the nut strips (1), the spacers (2) and the closing plate (3).
NOTE : Identify with its related slat track each set of:
____
-
the spacers (2)
-
the nut strips (1)
Installation of the Drive Adaptor - Slat Drive Mechanism. Figure 401/TASK 27-84-69-991-003
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FLIGHT CONTROLS 飛行操縱8(156)
