(f)
Put the pelmet (1) in position and install the screws (2).
(3)
Install the Air and Water connections (Ref. Fig. 402/TASK 25-31-41-991-014)
CUT, REMOVE AND DISCARD THE LOCKWIRE AS YOU DO THE
TASK. LOOSE LOCKWIRE CAN CUT OR BLIND YOU.
1_ Remove and discard the lockwire.
2_ Loosen the locknut.
3_ Adjust the tie rod end until the quick release pins (5) can
easily be installed.
4_ Tighten the locknut.
5_ Make sure that the tie rod end is in safety.
6_ Safety the locknut with MISCELLANEOUS (Material No. 19-010).
WARNING : MAKE SURE THAT THE POTABLE WATER SYSTEM IS DEPRESSURIZED. A
_______ PRESSURIZED SYSTEM CAN CAUSE INJURY TO PERSONS WHEN THEY DO WORK ON IT.
(a)
Remove the blanking plugs from the disconnected line ends.
(b)
Connect the potable water line (10) and the fitting (12) and tighten the nut (11).
(c)
Connect the hose (15) and the drain hose (13) and tighten the clamp (14).
(d)
Connect the hose (4) to the galley exhaust outlet pipe (6) and tighten the clamps (5).
(e)
Connect the hose (7) to the fresh air supply pipe (9) and tighten the clamp (8).
(4) Connect the power supply. (Ref. Fig. 401/TASK 25-31-41-991-038)
(a)
Install the bonding straps (12), the bolts (10), the washers (11) and the nuts (13) (Ref. TASK 20-28-00-912-004).
(b)
Put the clamps (1) in position on the wires.
(c)
Install the nuts (2) and the clamps (1).
(d)
Put the clamps (9) in position on the wires.
(e)
Install the bolts (7), the washers (8) and the clamps (9). CAUTION : REFER TO THE MATCH MARKS MADE DURING THE REMOVAL WHEN
_______ YOU CONNECT THE ELECTRICAL WIRES. IF YOU MAKE AN ERROR WHEN YOU CONNECT THE WIRES YOU WILL CAUSE DAMAGE TO EQUIPMENT.
(f)
Refer to the match marks and put the wires (6) in position.
(g)
Install the nuts (5).
(h)
Put the cover (3) in position and install the screws (4). WARNING : WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE LOCKWIRE.
_______ CUT, REMOVE AND DISCARD THE LOCKWIRE AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR BLIND YOU.
(i)
Safety the screws (4) with MISCELLANEOUS (Material No. 19-010).
(5) Seal the Splitline Joints
WARNING : MAKE SURE THAT THERE IS A GOOD FLOW OF AIR THROUGH THE WORK_______ AREA WHEN YOU USE SPECIAL MATERIALS. IF YOU GET ONE OF THESE MATERIALS ON YOUR SKIN, IN YOUR MOUTH OR IN YOUR EYES : -FLUSH IT AWAY WITH A FLOW OF CLEAN WATER FOR BETWEEN 10 AND 15 MINUTES. -GET IMMEDIATE MEDICAL AID IF IRRITATION OCCURS. DO NOT BREATHE THE FUMES FROM THE MATERIAL. DO NOT SMOKE WHEN YOU USE THE MATERIAL. DO NOT USE THE MATERIAL NEAR A FLAME, SPARKS OR SOURCES OF HEAT. THESE MATERIALS ARE DANGEROUS : THEY ARE POISONOUS, FLAMMABLE AND SKIN IRRITANTS.
WARNING : OBEY THE MANUFACTURER'S INSTRUCTIONS WHEN YOU USE_______ THIS/THESE MATERIAL/S. USE PROTECTIVE CLOTHING, RUBBER GLOVES, GOGGLES AND A MASK.
(a) Apply new BONDING AND ADHESIVE COMPOUNDS (Material No. 08-004A) into all the splitline joints.
R **ON A/C 051-099,
R Subtask 25-31-41-420-050-C
R A. Connect the Galley Splitline
R R NOTE : This procedure is only necessary if you removed the galley from____ the cabin.
R R NOTE : Unless specified TORQUE all nuts, bolts and screws (Ref. TASK 20-____ 21-11-911-001).
R R (1) Connect the Galley at the Splitline (Ref. Fig. 405A/TASK 25-31-41-991-020-B)
R R WARNING : SUPPORT THE UNIT/ASSEMBLY OR IT WILL FALL AND BECOME_______ DAMAGED OR INJURE PERSONNEL. THE UNIT/ASSEMBLY IS HEAVY.
R (a) Carefully put the module (10) in position with the module (13).
R (b) Put the strips (28) in position and install and the screws (12).
CES CES
R (c) Put the strips (14) and (15) in position and install the screws
R (10).
R (d) Install the casting (11) and the bolts (27).
R (e) Put the plate (24) in position and install the screws (22).
R (f) Install the shelf (23) and the screws (20).
R (g) Put the workdeck (30) and the plate (29) in position and install
R the screws (16).
R (h) Install the door (25) and the screws (26).
R (i) Put the drain pipe (17) in position on the sink drain (19) and
R install the clamp (18).
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM EQUIPMENT/FURNISHINGS 設備3(9)
