(4)
Make sure that the placards of the retained/new components are in the correct position and in good condition.
(a) If necessary install new placards.
-(Ref. AMM 11-32-25 P.Block 001).
-(Ref. TASK 11-00-00-400-007).
Subtask 25-41-41-420-050
B. Installation of the FWD Wall Unit R (Ref. Fig. 404/TASK 25-41-41-991-005-A)
(1)
Cut to length and put the new rubber strip (14) and the new rubber strip (15) in position on the floor panel.
(2)
Apply COMMON GREASE (Material No. 04-001) to the bush (5) and to the new packing (6) and put them in position.
(3)
Put the FWD wall unit (12) in position and align the front panel (8) and the passage wall (7) to the floor panel.
(a) Install and tighten the screws (13).
(4)
Connect the structure fittings.
(a)
Apply the COMMON GREASE (Material No. 04-001) to the bolts (1).
(b)
Install the bushes (3) and (2) and the bolts (1).
(c)
Apply STORAGE PRESERVATION (Material No. 15-008) to the head of the bolts (1).
(d)
Install the wall fitting cover (4) as necessary.
(5)
Install the washers (10) and the screws (9) in the passage wall (7).
(6)
Put the STEPLADDER 1.0 M (3.3 FT) in position.
EFF : ALL
25-41-41Page 436
(7) Connect the electrical connector.
(a)
Remove the blanking caps from the electrical connectors.
(b)
Make sure that the electrical connectors are clean and in the correct condition.
(c) Connect the electrical connector (11).
Subtask 25-41-41-420-051
C. Installation of the AFT Sidewall Assembly. R (Ref. Fig. 402/TASK 25-41-41-991-004-A)
(1)
Cut to length and put the new rubber strip (12) in position.
(2)
Apply COMMON GREASE (Material No. 04-001) to the bush (5) and to the new packing (6) and put them in position.
(3)
Put the AFT sidewall assembly (19) in position and install the screws (20).
(a)
Install the washers (10) and the screws (9).
(b)
Put the STEPLADDER 1.0 M (3.3 FT) in position.
(c)
Install the passage-wall attach screws (16) and the bracket attach screws (13).
(d)
Install the ceiling-panel attach screws (18) and the washers (17).
(e)
Put the angle (14) in position and install the screws (15).
EFF : ALL
25-41-41Page 437
(4) Connect the structure fittings
WARNING : MAKE SURE THAT THERE IS A GOOD FLOW OF AIR THROUGH THE WORK
_______ AREA WHEN YOU USE SPECIAL MATERIALS. IF YOU GET ONE OF THESE MATERIALS ON YOUR SKIN, IN YOUR MOUTH OR IN YOUR EYES : -FLUSH IT AWAY WITH A FLOW OF CLEAN WATER FOR BETWEEN 10 AND 15 MINUTES. -GET IMMEDIATE MEDICAL AID IF IRRITATION OCCURS. DO NOT BREATHE THE FUMES FROM THE MATERIAL. DO NOT SMOKE WHEN YOU USE THE MATERIAL. DO NOT USE THE MATERIAL NEAR A FLAME, SPARKS OR SOURCES OF HEAT. THESE MATERIALS ARE DANGEROUS : THEY ARE POISONOUS, FLAMMABLE AND SKIN IRRITANTS.
WARNING : OBEY THE MANUFACTURER'S INSTRUCTIONS WHEN YOU USE
_______
THIS/THESE MATERIAL/S.
USE PROTECTIVE CLOTHING, RUBBER GLOVES AND GOGGLES.
(a)
Get access to the lateral avionics compartment and:
-apply COMMON GREASE (Material No. 04-001) to the bolt (7),
-install the washer (8) and the bolt (7).
(b)
In the cabin:
-Apply the COMMON GREASE (Material No. 04-001) to the bolts (1).
-Install the bushes (3) and (2) and the bolts (1).
-Apply STORAGE PRESERVATION (Material No. 15-008) to the head of the bolts (1).
(c)
Install the covers (4).
(d)
Put the sealing angle (11) in position and install the washers
(10) and the screws (9).
(e)
Apply a bed of SEALANTS (Material No. 09-016) around the edges of the sealing angle (11).
(5) Connect the electrical connectors
CAUTION : REFER TO THE MATCH MARKS MADE DURING THE REMOVAL WHEN YOU
_______ CONNECT THE ELECTRICAL WIRES. INCORRECT CONNECTION OF THE WIRES WILL CAUSE DAMAGE TO EQUIPMENT.
(a) Remove the blanking caps from the electrical connectors.
EFF : ALL
25-41-41Page 438
Config-2 Aug 01/05
R
CES
(b)
Make sure that the electrical connectors are clean and in the correct condition.
(c)
Connect the electrical wires of the electrical harness (24) to the terminal 7330VT (25) (Ref. ESPM 25-25-41).
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM EQUIPMENT/FURNISHINGS 設備3(76)
