(c)
 Remove the bolts (1), the washers (2), the plates (3) and the shims (4).

 NOTE : Identify the position and number of the shims (4) for the
____
 installation procedure.

 (d)
 Remove the bolts (9) and the washers (10).

 (e)
 Remove the eccentric plugs (6) and the eccentric washers (5).

 (f)
 Carefully lift the galley off the blocks (13) and move it to the center of the aircraft.

 (g)
 Remove the shims (14). NOTE : Identify the position and number of the shims (14) for the

____
 installation procedure.

 (h)
 Remove the blocks (13).

 (i)
 Remove and discard the packings (12).

 (j) Remove the bushes (11).
 Subtask 25-33-41-020-052-A

 B. Disconnect the Galley Splitline NOTE : This procedure is only necessary if you must remove the galley
____
 from the cabin.

 NOTE : The galley splitline screws and bolts are painted red.
____

 (1)
 Disconnect the Splitline - Electrical Connections R (Ref. Fig. 408/TASK 25-33-41-991-005)

 (a)
 Remove the screws (25), the washers (24) and the disconnect the bonding straps (23).

 (b)
 Disconnect the electrical connector (27) from the electrical connector (26).

 (c)
 Put blanking caps on the disconnected electrical connectors.

 (2)
 Disconnect the Splitline - Potable Water and Drain Connections R (Ref. Fig. 408/TASK 25-33-41-991-005)

 (a)
 Remove the nut (5), the washer (4), the screw (2) and remove the clamp (7) and the bonding strap (3) from the hoses (1) and (6).

 (b)
 Disconnect the hose (6) from the hose (1).

 (c)
 Disconnect the pipe (9) from the union (10) on the water filter (8).

 (d)
 Remove and discard the cable ties (11) from the cable (12).

 (e)
 Disconnect the ring (16) from the fitting (17).

 (f)
 Remove the clamp (14), disconnect the hose (13) from the water filter (15).

 (g)
 Put blanking plugs on the disconnected line ends.

 (3)
 Disconnect the Galley at the Splitline R (Ref. Fig. 408/TASK 25-33-41-991-005)

 WARNING : SUPPORT THE UNIT/ASSEMBLY OR IT WILL FALL AND BECOME
_______ DAMAGED OR INJURE PERSONNEL. THE UNIT/ASSEMBLY IS HEAVY.
 (a)
 Remove the screws (19) and the pelmet (18).

 (b)
 Remove the screws (28) and the extractor (29).

 (c)
 Remove the screws (20) and the divider panels (21) and (22).

 (d)
 Remove the screws (39) and the panels (38).

 (e)
 Prevent damage to the component interface and the adjacent area.

R  Splitline - Electrical Connections Figure 407A/TASK 25-33-41-991-031 
R  EFF :  151-199,  25-33-41 Page 446 May 01/05
 CES 

 INTENTIONALLY BLANK

R  Galley 6483MM Splitline - G5 Figure 408/TASK 25-33-41-991-005- 13 (SHEET 1) 
R  EFF :  106-149, 201-299,  25-33-41 Page 448 May 01/05
 CES 

R  Galley 6483MM Splitline - G5 Figure 408/TASK 25-33-41-991-005- 23 (SHEET 2) 
R  EFF :  106-149, 201-299,  25-33-41 Page 449 May 01/05
 CES 

R  Galley 6483MM Splitline - G5 Figure 408/TASK 25-33-41-991-005- 33 (SHEET 3) 
R  EFF :  106-149, 201-299,  25-33-41 Page 450 May 01/05
 CES 

 (f) Remove the L-profiles (37).
 (g) Remove the screws (36), (35) , (43), (44), (45) and remove the
 brackets (40) andthe workbenches (41) and (42).
 (h) Remove the screws (31), the strip (47) and the galley modules
 (30) and (46).
 (i) Remove the screws (34) and the L-frames (33).
 (j) Remove the galley module (32). 
R  **ON A/C 151-199, 
R  Subtask 25-33-41-020-059-B 
R  A. Removal of the Galley Unit 
R  (1) Remove all the decorative material, if necessary. 
R  (2) Disconnect the Electrical Connections 
R  (Ref. Fig. 401C/TASK 25-33-41-991-022-B) 
R  (a) Remove and discard the lockwire from the screws (8). 
R  (b) Loosen the screws (8) and remove the cover (9). 
R  (c) Loosen the nuts (7): 
R  CAUTION : MAKE MATCH MARKS ON ALL THE ELECTRICAL WIRES BEFORE YOU_______ 
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM EQUIPMENT/FURNISHINGS 設備3(23)