曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

R R  (a) Clean the areas with DISINFECTANTS (Material No. 14-006B) and a lint-free cotton cloth MISCELLANEOUS (Material No. 19-003).
 (2) Make sure that the parts retained from the removed component are clean and in the correct condition.
 NOTE : Replace cadmium treated screws NAS1102-08-12 with corrosion____ resistant steel screws MS24693C52.
 (3) Do an inspection of the component interface and/or the adjacent area. 
R  Subtask 25-45-22-420-052 
R R  B. Installation of the Toilet Seat and the Seat Cover (Ref. Fig. 401/TASK 25-45-22-991-001-A) 
R R  (1) Engage the seat cover (3) and the seat (4) and install the pivot fittings (7). 
R R  (2) Put the seat (4) and the seat cover (3) in position on the shroud (1) and install the washers (5) and nuts (6).
 Subtask 25-45-22-420-050-A 
R R C. Installation of the Toilet Shroud for the Vacuum Toilet (Ref. Fig. 401/TASK 25-45-22-991-001-A) 
(1) Make sure that the work area is clean and clear of tool(s) and other items.

 EFF : ALL
25-45-22Page 405
Feb 01/05

 (2) Put the toilet shroud (1) in position.
 (3) Install the screws (2).
 NOTE : Make sure you install corrosion resistant steel screws____ MS24693C52. 
R 
R R  (4) Make sure that all of the placards of the retained/new components are in the correct position and in a good condition. 
R R  (a) If necessary install new placards (Ref. TASK 11-00-00-400-007) and (Ref. AMM 11-32-25 P.Block 001).
 5. Close-up________
 Subtask 25-45-22-862-050
 A. De-energize the ground service network (Ref. TASK 24-42-00-862-001).

 EFF : ALL
25-45-22Page 406

 HAND GRIP - REMOVAL/INSTALLATION
________________________________
 TASK 25-45-23-000-001 Removal of the Hand Grip
 1.
 Reason for the Job

__________________
 Self Explanatory

 2.
 Job Set-up Information

______________________
 A. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
24-42-00-861-001  Energize the Ground Service Network from the External Power 25-45-23-991-001 Fig. 401
 3. Job Set-up
__________ Subtask 25-45-23-861-050
 A. Aircraft Maintenance Configuration
 (1) Energize the ground service network
 (Ref. TASK 24-42-00-861-001).

 4. Procedure
_________ Subtask 25-45-23-020-050
 A. Removal of the Hand Grip
 (Ref. Fig. 401/TASK 25-45-23-991-001)

 (1)
 Support the hand grip (1) and remove the pins (2).

 (2)
 Remove the hand grip (1).

 EFF : ALL
25-45-23Page 401

 Hand Grip
 Figure 401/TASK 25-45-23-991-001
 EFF :  ALL  25-45-23 Page 402 
Feb 01/98
 CES 

 

 TASK 25-45-23-400-001 Installation of the Hand Grip
 1.
 Reason for the Job

__________________
 Self Explanatory

 2.
 Job Set-up Information

______________________
 A. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
24-42-00-861-001  Energize the Ground Service Network from the External Power 24-42-00-862-001 De-energize the Ground Service Network Supplied from the External Power 25-45-23-991-001 Fig. 401
 3. Job Set-up
__________ Subtask 25-45-23-860-050
 A. Aircraft Maintenance Configuration
 (1) Make sure that the ground service network is energized
 (Ref. TASK 24-42-00-861-001).

 4. Procedure
_________ Subtask 25-45-23-210-050
 A. Preparation for Installation
 (1)
 Clean the component interface and/or the adjacent area.

 (2)
 Make sure that the parts retained from the removed component are clean and in the correct condition.

 (3)
 Do an inspection of the component interface and/or the adjacent area.

 EFF : ALL
25-45-23Page 403

 Subtask 25-45-23-420-050
 B. Installation of the Hand Grip
 (Ref. Fig. 401/TASK 25-45-23-991-001)

 (1)
 Put the hand grip (1) on the special screws (3).

 (2)
 Install the pins (2). If the pin holes are not aligned, do the following;
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM EQUIPMENT/FURNISHINGS 設備3(126)