-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------**ON A/C ALL
 123VU FWD GALLEY/FEEDER F 16MC AC10 **ON A/C 301-399,
 123VU FWD GALLEY/FEEDER C 1MC AE03 123VU FWD GALLEY/FEEDER D 2MC AE02
R **ON A/C 401-499,
R 123VU FWD GALLEY/FEEDER D 2MC AD04 R 123VU FWD GALLEY/FEEDER C 1MC AF09
 **ON A/C ALL
 Subtask 25-31-41-560-053
 C. Preparation of the Replacement Component NOTE : To install the galley through the aircraft door it is necessary to
____ disconnect the galley splitline (Ref. TASK 25-31-41-000-001).
 Subtask 25-31-41-210-050
 D. Preparation for Installation
 (1)
 Clean the component interface and/or the adjacent area.

 (2)
 Do a visual inspection of the component interface and/or the adjacent area.

 (3)
 Make sure that the parts retained from the removed component are clean and in the correct condition.

 EFF : ALL
25-31-41Page 460

 4. Procedure
_________ R **ON A/C 001-049, 101-105,
 Subtask 25-31-41-420-050
 A. Connect the Galley Splitline NOTE : This procedure is only necessary if you removed the galley from
____
 the cabin.

 NOTE : Unless specified TORQUE all nuts, bolts and screws (Ref. TASK 20-
____
 21-11-911-001).

 NOTE : The splitline screws and bolts are painted red.
____
 (1) Connect the Galley at the Splitline
 (Ref. Fig. 405/TASK 25-31-41-991-020)

 (a)
 Prevent damage to the component interface and the adjacent area. WARNING : SUPPORT THE UNIT/ASSEMBLY OR IT WILL FALL AND BECOME

_______ DAMAGED OR INJURE PERSONNEL. THE UNIT/ASSEMBLY IS HEAVY.

 (b)
 Carefully put the single modules in position.

 (c)
 Install the screws (1) and (2).

 (d)
 Install the screws (4) and the covers (3).

 (e)
 Put the stowage cart bumper (12) in position.

 (f)
 Install the screws (11) and the washers (10).

 (g)
 Put the bonding wire (6) in position on the ground stud (5).

 (h)
 Install the washers (7) and the nuts (8).

 (i)
 Connect the electrical connectors (9).

 EFF : ALL
25-31-41Page 461

 Subtask 25-31-41-420-062
 B. Installation of the Galley Unit NOTE : Unless specified TORQUE all nuts, bolts and screws. (Ref. TASK 20-
____
 21-11-911-001)

 (1)
 Install the Lower Attachments
 (Ref. Fig. 404/TASK 25-31-41-991-019)

 (a)
 Apply COMMON GREASE (Material No. 04-004A) to the bushes (17).

 (b)
 Install the bushes (17) in the floor hardpoints.

 (c)
 Install the new packing (16).

 (d)
 Put the blocks (15) in position on the hardpoints.

 (e)
 Apply COMMON GREASE (Material No. 04-004A) to the threads of the bolts (7).

 (f)
 Install the bolts (7) and the washers (10).

 (g)
 Install the shims (14). WARNING : SUPPORT THE UNIT/ASSEMBLY OR IT WILL FALL AND BECOME

_______ DAMAGED OR INJURE PERSONNEL. THE UNIT/ASSEMBLY IS HEAVY.

 (h)
 Put the galley in position on the blocks (15).

 (i)
 Install the eccentric plugs (13) and the eccentric bushes (12). NOTE : If necessary turn the eccentric plugs (13) and the

____ eccentric bushes (12) until the holes in the galley mounting are aligned with the holes in the blocks (15).

 (j)
 Install the plates (11), the washers (9) and the bolts (8).

 (k)
 Install the covers (5) and the screws (6).

 (l)
 Install the covers (3) and the screws (4).

 (m)
 Install the rub strips (2) and the screws (1).

 (2)
 Install the Upper Attachments (Ref. Fig. 403/TASK 25-31-41-991-018)

 (a)
 Put the tie rods (4) in position and install the quick-release pins (5).

 (b)
 If necessary, remove and adjust the tie rods (4). WARNING : WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE LOCKWIRE.

_______

 (c)
 Put the fresh air hose (8) in position on the fresh air supply outlet (7).

 (d)
 Install the clamp (9).

 (e)
 Install the panel (10) and fasten the quick-release fasteners (3).
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM EQUIPMENT/FURNISHINGS 設備3(8)