曝光臺 注意防騙 網(wǎng)曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

The heading/track preset allows the pilot to preset a takeoff or go-around heading or track before
commanding the aircraft to take up that heading or track (manual activation).
The flight crew can enter a heading or a track preset while the aircraft is on the ground and until
takeoff.
A318/A319/A320/A321 FLIGHT CREW
OPERATING MANUAL
PROCEDURES
NORMAL PROCEDURES
SYSTEMS RELATED PROCEDURES - FMS
A318/A319/A320/A321 FLEET PRO-NOR-SRP-01-10 P 58/58
FCOM 19 AUG 10
PROCEDURE
�� Before takeoff :
SET the appropriate HDG or TRK in the FCU window.
This disarms the navigation mode and allows the runway mode to remain engaged after
takeoff.
�� After takeoff :
PULL HDG/TRK selector knob.
The heading or track mode engages on the preset value.
The direction in which the pilot rotates the HDG/TRK selection knob usually determines the
direction of the turn. A left rotation (decreasing heading) produces a left turn ; a right rotation
produces a right turn.
However, when a heading has been preset before takeoff or go-around, the direction of the
turn will be such as to cause the shortest turn at the moment of engagement.
CANCELLING THE HEADING/TRACK PRESET FUNCTION
The pilot can cancel the heading preset by pushing the HDG/TRK selector knob back in again.
This engages or arms the NAV mode.
A318/A319/A320/A321 FLIGHT CREW
OPERATING MANUAL
PROCEDURES
NORMAL PROCEDURES
SYSTEMS RELATED PROCEDURES - FMS
A318/A319/A320/A321 FLEET PRO-NOR-SRP-01-15 P 1/4
FCOM 19 AUG 10
Before Pushback or Start
CHANGE OF RUNWAY
Applicable to:
PRESS the F-PLN key on the MCDU.
SELECT the LAT REV at origin.
SELECT the DEPARTURE prompt [ 1L ].
SELECT the new RWY in use.
SELECT the appropriate SID and TRANS.
CHECK the resulting temporary F-PLN and INSERT it.
ENTER the new V1, VR, V2, FLEX TEMP (or derated thrust if installed) and CONF, as appropriate.
Note: If the previously selected SID is compatible with the new runway, it automatically appears
in the temporary flight plan. Any revision the flight crew may have made to the previous SID
will not be transferred.
If the pilot still wants it, he has to reenter it.
A318/A319/A320/A321 FLIGHT CREW
OPERATING MANUAL
PROCEDURES
NORMAL PROCEDURES
SYSTEMS RELATED PROCEDURES - FMS
A318/A319/A320/A321 FLEET PRO-NOR-SRP-01-15 P 2/4
FCOM 19 AUG 10
CHANGE OF RUNWAY
Applicable to:
CHANGE OF RUNWAY
Applicable to:
PRESS the F-PLN key on the MCDU.
SELECT the LAT REV at origin.
SELECT the DEPARTURE prompt [ 1L ].
SELECT the new RWY in use.
SELECT the appropriate SID and TRANS.
CHECK the resulting temporary F-PLN and INSERT it.
Scratchpad display the CHECK TO DATA message, if the PERF TO page was already filled in.
A318/A319/A320/A321 FLIGHT CREW
OPERATING MANUAL
PROCEDURES
NORMAL PROCEDURES
SYSTEMS RELATED PROCEDURES - FMS
A318/A319/A320/A321 FLEET PRO-NOR-SRP-01-15 P 3/4
FCOM 19 AUG 10
ENTER the new V1, VR, V2, FLEX TEMP or CONF, as appropriate.
Note: If the previously selected SID is compatible with the new runway, it automatically appears
in the temporary flight plan. Any revision the flight crew may have made to the previous SID
will not be transferred.
If the pilot still wants it, he has to reenter it.
CHANGE OF RUNWAY
Applicable to:
,
,
MSN,,
4538,,
PRESS the F-PLN key on the MCDU.
SELECT the LAT REV at origin.
SELECT the DEPARTURE prompt [ 1L ].
SELECT the new RWY in use.
SELECT the appropriate SID and TRANS.
A318/A319/A320/A321 FLIGHT CREW
OPERATING MANUAL
PROCEDURES
NORMAL PROCEDURES
SYSTEMS RELATED PROCEDURES - FMS
A318/A319/A320/A321 FLEET PRO-NOR-SRP-01-15 P 4/4
FCOM 19 AUG 10
CHECK the resulting temporary F-PLN and INSERT it.
Scratchpad display the CHECK TO DATA message, if the PERF TO page was already filled in.
ENTER the new V1, VR, V2, FLEX TEMP or CONF, as appropriate.
The previously-entered values, adjacent to the boxes, may be re-selected by pressing the CONFIRM
TO DATA* prompt on [ 6R ].
Note: In case of a runway change, any previous lateral modification performed on the active
DEPARTURE procedure may lead to additional waypoint stacking in the temporary F-PLN.
The crew has to check and revise it, as necessary.
Refer to DSC-22_20-30-10-18 CHANGING THE DEPARTURE/ARRIVAL.
TAKEOFF FROM INTERSECTION
Applicable to: ALL
Use RTOW or FCOM to revise takeoff parameters :
PRESS the [PERF] key on MCDU
ENTER the takeoff shift
ENTER the new V1, VR, V2, FLX TEMP, or CONF, as appropriate
　
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320機組操作手冊FLIGHT CREW OPERATING MANUAL 12(64)