曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

‐ The selected speed target is active.
‐ The primary flight display shows the target speed in blue.
‐ The FCU’s speed window displays the new speed or Mach number.
Applicable to:
CLIMB SPEED PRESELECTION
If the managed speeds for the initial climb are not suitable, the pilot can preselect an appropriate
climb speed on the “PERF CLB ” page, as long as the climb phase is not active.
A318/A319/A320/A321 FLIGHT CREW
OPERATING MANUAL
PROCEDURES
NORMAL PROCEDURES
SYSTEMS RELATED PROCEDURES - FMS
A318/A319/A320/A321 FLEET PRO-NOR-SRP-01-10 P 53/58
FCOM 19 AUG 10
The CLB SPD preselection applies, when the :
‐ ATC specifies an initial climb speed.
‐ Initial climb speed must be lower than normal because :
• There are to be turns greater than 120 ° in the initial climb out.
• Obstacle clearance, or some other situation, requires a high climb angle.
• The airfield has a risk area to be quickly cleared (birds reported, for example).
PROCEDURE
PRESS the PERF key on the MCDU.
The PERF TAKE OFF page is displayed.
SELECT the PERF CLB page by pressing [6 R] (“NEXT PHASE” prompt).
WRITE a climb speed and ENTER it.
To revert to managed speed, select MANAGED by pressing [3L].
A318/A319/A320/A321 FLIGHT CREW
OPERATING MANUAL
PROCEDURES
NORMAL PROCEDURES
SYSTEMS RELATED PROCEDURES - FMS
A318/A319/A320/A321 FLEET PRO-NOR-SRP-01-10 P 54/58
FCOM 19 AUG 10
When the aircraft is transitioning into the climb phase, the preselected value becomes the target
speed :
‐ The selected speed target is active.
‐ The primary flight display shows the target speed in blue.
‐ The FCU’s speed window displays the new speed or Mach number.
Applicable to:
,
,
MSN,,
4538,,
CRUISE MACH (SPEED) PRESELECTION
The pilot preselects a cruise Mach, when a Mach number other than the ECON cruise Mach
number is required.
When the aircraft transitions to the cruise phase, the speed target symbol goes to the preselected
value and “SELECTED” becomes the active speed mode (blue target on PFD, target MACH
shown in the speed/Mach window of the FCU).
A318/A319/A320/A321 FLIGHT CREW
OPERATING MANUAL
PROCEDURES
NORMAL PROCEDURES
SYSTEMS RELATED PROCEDURES - FMS
A318/A319/A320/A321 FLEET PRO-NOR-SRP-01-10 P 55/58
FCOM 19 AUG 10
PROCEDURE
PRESS the PERF key on the MCDU.
PRESS the “NEXT PHASE” [6R] key on the MCDU, until the CRZ page is accessed.
WRITE a cruise Mach (or speed) in the scratchpad and ENTER it in [4L].
To revert to managed speed, PRESS [3L].
When the cruise phase is active, you cannot preselect a cruise Mach or speed.
Applicable to:
CRUISE MACH (SPEED) PRESELECTION
The pilot preselects a cruise Mach, when a Mach number other than the ECON cruise Mach
number is required.
When the aircraft transitions to the cruise phase, the speed target symbol goes to the preselected
value and “SELECTED” becomes the active speed mode (blue target on PFD, target MACH
shown in the speed/Mach window of the FCU).
A318/A319/A320/A321 FLIGHT CREW
OPERATING MANUAL
PROCEDURES
NORMAL PROCEDURES
SYSTEMS RELATED PROCEDURES - FMS
A318/A319/A320/A321 FLEET PRO-NOR-SRP-01-10 P 56/58
FCOM 19 AUG 10
PROCEDURE
PRESS the PERF key on the MCDU.
PRESS the “NEXT PHASE” [6R] key on the MCDU, until the CRZ page is accessed.
WRITE a cruise Mach (or speed) in the scratchpad and ENTER it in [4L].
To revert to managed speed, PRESS [3L].
When the cruise phase is active, you cannot preselect a cruise Mach or speed.
Applicable to:
CRUISE MACH (SPEED) PRESELECTION
The pilot preselects a cruise Mach, when a Mach number other than the ECON cruise Mach
number is required.
When the aircraft transitions to the cruise phase, the speed target symbol goes to the preselected
value and MACH (or SPD) becomes selected (blue target on PFD, target MACH shown in the
speed/Mach window of the FCU).
A318/A319/A320/A321 FLIGHT CREW
OPERATING MANUAL
PROCEDURES
NORMAL PROCEDURES
SYSTEMS RELATED PROCEDURES - FMS
A318/A319/A320/A321 FLEET PRO-NOR-SRP-01-10 P 57/58
FCOM 19 AUG 10
PROCEDURE
PRESS the PERF key on the MCDU.
PRESS the “NEXT PHASE” [6R] key on the MCDU, until the CRZ page is accessed.
WRITE a cruise Mach (or speed) in the scratchpad and ENTER it in [4L].
To revert to managed speed, PRESS [3L].
When the cruise phase is active, you cannot preselect a cruise Mach or speed.
Applicable to: ALL
ENTERING A HEADING/TRACK PRESET FUNCTION
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320機組操作手冊FLIGHT CREW OPERATING MANUAL 12(63)