曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

(e) Select SET ON? from the RUD PRES LIMIT? menu. The display will show CMD ON, SET
OFF?
NOTE: You only have 75 seconds to complete the next 3 tasks. If you do not finish in 75
seconds, you will have to repeat the test and start with the steps to use the FSEU
to command the RPL to the "LOW" state.
SUBTASK 27-21-00-980-004-002
(2) Push the left rudder pedal until it touches the forward quadrant stop and hold.
SUBTASK 27-21-00-980-005-002
(3) Manually hold the main rudder PCU lower control rod at location B (Figure 505) and pull forward
with a force of approximately 30 to 40 lbs (133 to 178 newtons) until it touches the stop and hold.
NOTE: To make the test easy, you may skip this step. If you skip this step and the test fails,
then you must repeat the test and perform this step.
SUBTASK 27-21-00-700-003-002
(4) Verify voltage between pin 18 and pin 20 of connector D10064 on the E1-EE shelf is between 1.87
VDC to 2.62 VDC.
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN 006-099, 101-122; GUN 001-005, 155-157, 201-999
POST SB 737-27-1253
27-21-00
Config 2
Page 565
Oct 10/2007
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
SUBTASK 27-21-00-980-020-002
(5) Release the main rudder PCU control rod.
SUBTASK 27-21-00-980-021-002
(6) Release the rudder pedal.
SUBTASK 27-21-00-860-131-002
(7) The display screen on the FSEU should show CMD ON, SET OFF?.
Select YES. The display will show CMD OFF, SET ON?.
SUBTASK 27-21-00-980-022-002
(8) Push the left rudder pedal until it touches the forward quadrant stop and hold.
SUBTASK 27-21-00-980-023-002
(9) Manually hold the main rudder PCU lower control rod at location B (Figure 505) and pull forward
with a force of approximately 30 to 40 lbs (133 to 178 newtons) until it touches the stop and hold.
NOTE: To make the test easy, you may skip this step. If you skip this step and the test fails,
then you must repeat the test and perform this step.
SUBTASK 27-21-00-700-004-002
(10) Verify voltage between pin 18 and pin 20 of connector D10064 on the E1-EE shelf is less than 1.87
VDC.
SUBTASK 27-21-00-980-006-002
(11) Release the main rudder PCU lower control rod.
SUBTASK 27-21-00-980-007-002
(12) Release the left rudder pedal.
NOTE: You have completed the test of system B in the extend direction.
G. Rudder main PCU system B Internal Leakage Check in the retract direction.
SUBTASK 27-21-00-860-132-002
(1) Use the FSEU, located on the E-1 shelf in the main equipment center, to command the Rudder
Pressure Limiters (RPL) to the "LOW" pressure state. Do these steps:
NOTE: The command will remains active for only 75 seconds after it is set.
(a) Push the ON/OFF button on the front panel of the flap/slat electronics unit (FSEU), on E
shelf, to turn on the display.
NOTE: The display will show EXISTING FAULTS?
(b) Select OTHER FUNCTNS? from the MAIN MENU on the FSEU. The display will show SET
OUTPUTS?
(c) Select SET OUTPUTS? from the OTHER FUNCTNS? menu. The display will show RUD
PRES LIMIT?
(d) Select RUD PRES LIMIT? from the SET OUTPUTS? menu. The display will show SET ON?
(e) Select SET ON? from the RUD PRES LIMIT? menu. The display will show CMD ON, SET
OFF?
NOTE: You only have 75 seconds to complete the next 3 tasks. If you do not finish in 75
seconds, you will have to repeat the test and start with the steps to use the FSEU
to command the RPL to the "LOW" state.
SUBTASK 27-21-00-980-008-002
(2) Push the right rudder pedal until it touches the forward quadrant stop and hold.
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN 006-099, 101-122; GUN 001-005, 155-157, 201-999
POST SB 737-27-1253
27-21-00
Config 2
Page 566
Oct 10/2007
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
SUBTASK 27-21-00-980-009-002
(3) Manually hold the main rudder PCU lower control rod at location B (Figure 505) and pull aft with
a force of approximately 30 to 40 lbs (133 to 178 newtons) until it touches the stop and hold.
NOTE: To make the test easy, you may skip this step. If you skip this step and the test fails,
then you must repeat the test and perform this step.
SUBTASK 27-21-00-700-005-002
(4) Verify voltage between pin 18 and pin 20 of connector D10064 on the E1-EE shelf is between 7.37
VDC to 8.13 VDC.
SUBTASK 27-21-00-980-024-002
(5) Release the main rudder PCU control rod.
SUBTASK 27-21-00-980-025-002
(6) Release the rudder pedal.
SUBTASK 27-21-00-860-133-002
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-600/700/800/900 AIRCRAFT MAINTENANCE MANUAL飛機維護手冊2(74)