曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

(d) Put the parking brakes on.
(e) Put the FLT CONTROL A and B and SPOILER A and B switches, on the P5 panel, in the ON
position.
(f) Cycle the flaps from up to 40 to up two times.
NOTE: The leading edge flaps and slats will also move.
(g) Cycle the rudder pedals ten times.
(h) Cycle the control wheel ten times.
(i) Cycle the control column ten times.
SUBTASK 27-21-00-860-119-001
(9) Do these steps to put the airplane in its initial condition:
(a) Put the reverse thrust levers in the STOWED position.
(b) Put the stabilizer trim in the green band.
NOTE: The stabilizer indicator is on the control stand.
(c) Set the aileron trim to zero.
NOTE: The aileron trim indicator is on the control wheel.
(d) Set the rudder trim to zero.
NOTE: The rudder trim indicator is on the P8 panel.
(e) Do these steps to turn off the antiskid system:
1) Open these circuit breakers and install safety tags:
F/O Electrical System Panel, P6-3
Row Col Number Name
A 16 C01345 LANDING GEAR AUTOBRAKE BITE CONT 2
A 18 C00583 LANDING GEAR AUTOBRAKE BITE CONT 1
E 16 C00196 LANDING GEAR ANTISKID INBD
E 18 C00195 LANDING GEAR ANTISKID OUTBD
(f) Put the YAW DAMPER switch, on the P5 panel, in the OFF position.
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN 001-005, 155-157, 201-999 PRE SB 737-27-1253 27-21-00
Config 1
Page 557
Jun 10/2007
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
(g) Put the A/P ENGAGE switches, on the mode control panel (MCP), in the OFF position.
(h) Put the LANDING GEAR handle, on the P2 panel, in the OFF position.
(i) Put the SPEED BRAKE lever, on the control stand, in the DOWN position.
(j) Put the FLT CONTROL A and B and SPOILER A and B switches, on the P5 panel, in the OFF
position.
(k) Set the flap control lever to 25 units and make sure that the flaps move.
(l) Open this circuit breaker and install safety tag:
Power Distribution Panel Number 2, P92
Row Col Number Name
F 2 C01449 STANDBY HYDRAULIC PUMP
(m) Put the arm switch for the ALTERNATE FLAPS in the ARM position.
(n) Set the flap control lever to 40 units (the flaps will not move).
G. Rudder PCU Internal Leakage Check (Hydraulic System B)
SUBTASK 27-21-00-710-074-001
(1) Put the FLT CONTROL B switch in the ON position.
NOTE: FLT CONTROL A must be in the OFF position.
SUBTASK 27-21-00-710-075-001
(2) Make sure the pressure in system B is a minimum of 2800 psi (19305 kPa).
SUBTASK 27-21-00-710-077-001
(3) Put the YAW Damper switch, on the P5 panel, in the ON position.
SUBTASK 27-21-00-710-078-001
WARNING: MAKE SURE THAT PERSONS AND EQUIPMENT ARE CLEAR OF THE RUDDER AND
THE PCU ACTUATORS. THE RUDDER AND PCU ACTUATORS MOVE QUICKLY. THIS
CAN CAUSE INJURY TO PERSONS AND DAMAGE TO EQUIPMENT.
(4) Put the YAW DAMPER POWER switch, on the test box, SPL-1805, to the ON position.
NOTE: The red indicator light on the test box should come on.
The rudder might move slowly to the right or left as much as 3 degrees.
SUBTASK 27-21-00-710-079-001
(5) Put the RUDDER TRAVEL DIRECTION switch on the test box to the LEFT position.
NOTE: The green indicator light on the test box should come on and the rudder should move to
the left unless it is already at the left position.
SUBTASK 27-21-00-710-080-001
(6) When the hydraulic flow becomes stable, record the amperage value from the ammeter as
Value # 1: ____________
SUBTASK 27-21-00-710-081-001
(7) Push the left rudder pedal until it touches the forward quadrant stop and hold.
SUBTASK 27-21-00-710-082-001
(8) When the hydraulic flow becomes stable, record the amperage value from the ammeter as
Value # 2: ____________
SUBTASK 27-21-00-710-083-001
(9) Put the left rudder pedal to the neutral position.
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN 001-005, 155-157, 201-999 PRE SB 737-27-1253 27-21-00
Config 1
Page 558
Jun 10/2007
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
SUBTASK 27-21-00-710-084-001
(10) Calculate and record the difference in amperage values with this formula:
(a) Value # 2 minus Value # 1 : _______________ (amps)
SUBTASK 27-21-00-710-085-001
(11) Make sure the difference in amperage values is between -0.7 amps and 1.5 amps.
SUBTASK 27-21-00-710-086-001
(12) If the difference in amperage values is not in the given range, replace the rudder PCU.
NOTE: After installation of the new PCU, continue the system B portion of this check.
SUBTASK 27-21-00-710-087-001
(13) Put the RUDDER TRAVEL DIRECTION switch on the test box to the RIGHT position.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-600/700/800/900 AIRCRAFT MAINTENANCE MANUAL飛機維護手冊2(43)