曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

position.
1) Make sure the position of the captain’s control column is in 6.1 - 7.7 degrees of the
vertical position (90 degrees).
(g) Remove the adapter, SPL-1674 and control column assembly protractor, SPL-1680 from the
captain’s control column.
(h) Attach the adapter, SPL-1674 and control column assembly protractor, SPL-1680 to the first
officer’s control column (Figure 514).
(i) Move the first officer’s control column lightly forward and aft to make sure it is in the neutral
position (Figure 514).
1) Make sure the position of the captain’s control column is in 6.1 - 7.7 degrees of the
vertical position.
(j) Remove the adapter, SPL-1674 and control column assembly protractor, SPL-1680 from the
first officer’s control column.
SUBTASK 27-31-00-730-008
(2) Do the elevator centering test:
(a) Set the FLT CONTROL B switch on the forward overhead panel, P5, to the OFF position.
(b) Make sure the FLT CONTROL A switch on the forward overhead panel, P5, is in the ON
position.
(c) Make sure the captain’s control column is at the neutral position.
1) Make sure the right elevator aligns with the index mark in +/- 0.06 inch (+/- 1.5 mm)
(Figure 505).
(d) Set the FLT CONTROL B switch to the ON position.
1) Make sure the right elevator aligns with the index mark in +/- 0.06 inch (+/- 1.5 mm).
(e) Set the FLT CONTROL A switch to the OFF position.
(f) Make sure the FLT CONTROL B switch is in the ON position.
1) Make sure the right elevator aligns with the index mark in +/- 0.06 inch (+/- 1.5 mm).
(g) Set the FLT CONTROL A switch to the ON then to the OFF position.
1) Make sure there is less than 0.02 inch (0.5 mm) movement at the right elevator trailing
edge.
(h) Set the FLT CONTROL B switch to the OFF then to the ON then to the OFF position.
1) Make sure there is less than 0.02 inch (0.5 mm) movement at the right elevator trailing
edge.
(i) Set the FLT CONTROL A and B switches to the ON position.
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-31-00
Page 578
Oct 10/2006
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
(j) Make sure the captain’s control column is at the neutral position.
1) Make sure the right elevator aligns with the index mark in +/- 0.06 inch (+/- 1.5 mm).
(k) Move the captain’s control column forward approximately 2 degrees and release.
1) Make sure the right elevator trailing edge aligns with the index mark in 0.00 +/- 0.12
inch (0.0 +/- 3.0 mm).
(l) Move the captain’s control column aft approximately 2 degrees and release.
1) Make sure the right elevator trailing edge aligns with the index mark in 0.00 +/- 0.12
inch (0.0 +/- 3.0 mm).
H. Put the Airplane Back to Its Usual Condition
SUBTASK 27-31-00-860-078
(1) Do this task: Put the Elevator Hydraulic systems A and B Back to the Condition Before the
Pressurization, TASK 27-31-00-840-801.
SUBTASK 27-31-00-410-014
(2) Close this access panel:
Number Name/Location
311BL Stabilizer Trim Access Door
------------------------- END OF TASK ---------------------------
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-31-00
Page 579
Oct 10/2006
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
Elevator Control Column Protractor Installation
Figure 514/27-31-00-990-813
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-31-00
Page 580
Oct 10/2006
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
TASK 27-31-00-700-809
19. Control Column Power Force - Test
(Figure 502, Figure 514, Figure 523)
A. General
(1) Use this test to make sure the control columns move with the correct input force.
B. References
Reference Title
27-31-00-700-801 Null Procedure - Mach Trim Actuator (P/B 201)
27-31-00-800-801 Elevator Hydraulic System A and B - Pressurization (P/B 201)
27-31-00-800-802 Remove Pressure from the Elevator Hydraulic Systems A and B
(P/B 201)
27-31-00-840-801 Put the Elevator Hydraulic systems A and B Back to the Condition
Before the Pressurization (P/B 201)
C. Tools/Equipment
NOTE: When more than one tool part number is listed under the same "Reference" number, the
tools shown are alternates to each other within the same airplane series. Tool part numbers
that are replaced or non-procurable are preceded by "Opt:", which stands for Optional.
Reference Description
COM-1557 Gauge - Force
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-600/700/800/900 AIRCRAFT MAINTENANCE MANUAL飛機維護手冊2(158)