曝光臺 注意防騙 網(wǎng)曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

"YES" BUTTON ON THE SMYD NO. 2. THIS CAN CAUSE INJURY TO
PERSONS AND DAMAGE TO EQUIPMENT.
6) Push the YES button when the RUDDER CLEARED? shows on the display.
7) Push the YES button when the FLT CTRL A STBY? shows on the display.
8) Push the YES button when the FLT CTRL B STBY? shows on the display.
9) Push the YES button when YAW DMPR ENGAGED? shows on the display.
10) Push the YES button when the ZERO COMMAND? shows on the display.
NOTE: A yaw damper command value and LVDT position will show for 10 seconds
each, then the END ZERO COMMAND? will show on the display. You can push
the NO button to show these values again.
(h) Move the captain’s left rudder pedal approximately 0.5 in. (12.7 mm) forward and release.
1) Make sure the rudder goes back to the neutral position.
(i) Move the captain’s right rudder pedal approximately 0.5 in. (12.7 mm) forward and release.
1) Make sure the rudder goes back to the neutral position.
(j) Push and release the ON/OFF button on the SMYD No. 2.
SUBTASK 27-21-00-860-107-002
(5) Set the YAW DAMPER switch on the P5-3 overhead panel to the OFF position.
SUBTASK 27-21-00-860-108-002
(6) Do this task: Remove Electrical Power, TASK 24-22-00-860-812.
SUBTASK 27-21-00-860-109-002
(7) Do this task: Put the Rudder Hydraulic systems A, B, and Standby Back to the Condition
Before the Pressurization, TASK 27-21-00-840-801.
------------------------- END OF TASK ---------------------------
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN 006-099, 101-122; GUN 001-005, 155-157, 201-999
POST SB 737-27-1253
27-21-00
Config 2
Page 551
Oct 10/2007
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
TASK 27-21-00-700-816-002
10. Rudder Pedal Forces Test
(Figure 504)
A. General
(1) Use this test to make sure the rudder pedals operate with the correct forces.
NOTE: You must measure the forces with the pedal moving away from the neutral position. If
the pedal moves more than the specified distances, you must repeat the test and start
with the pedal at neutral position.
B. References
Reference Title
27-21-00-800-801 Rudder Hydraulic System A, B, or Standby Pressurization (P/B 201)
27-21-00-840-801 Put the Rudder Hydraulic systems A, B, and Standby Back to the
Condition Before the Pressurization (P/B 201)
C. Tools/Equipment
NOTE: When more than one tool part number is listed under the same "Reference" number, the
tools shown are alternates to each other within the same airplane series. Tool part numbers
that are replaced or non-procurable are preceded by "Opt:", which stands for Optional.
Reference Description
SPL-1681 Adapter - Force Check Tool, Rudder Pedal
(Part #: F80212-30, Supplier: 81205, A/P Effectivity: 737-100, -200,
-200C, -300, -400, -500, -600, -700, -700C, -700ER, -700QC, -800, -900,
-900ER, -BBJ)
D. Location Zones
Zone Area
211 Flight Compartment - Left
212 Flight Compartment - Right
325 Vertical Fin - Rudder
E. Procedure
SUBTASK 27-21-00-860-110-002
WARNING: MAKE SURE THAT PERSONS AND EQUIPMENT ARE CLEAR OF ALL CONTROL
SURFACES BEFORE YOU SUPPLY HYDRAULIC POWER. AILERONS, RUDDER,
ELEVATORS, FLAPS, SPOILERS, SLATS, AND THRUST REVERSERS CAN MOVE
QUICKLY WHEN YOU SUPPLY HYDRAULIC POWER. THIS CAN CAUSE INJURY TO
PERSONS AND DAMAGE TO EQUIPMENT.
(1) Pressurize the rudder hydraulic systems A and B. To pressurize them, do this task: Rudder
Hydraulic System A, B, or Standby Pressurization, TASK 27-21-00-800-801.
SUBTASK 27-21-00-730-019-002
(2) Do the test of the rudder pedal forces test:
(a) Set the captain’s and first officer’s rudder pedal adjustment cranks to the middle position.
(Figure 501)
(b) Make sure the rudder pedals are in the neutral position.
(c) Install adapter, SPL-1681 on the captain’s left rudder pedal.
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN 006-099, 101-122; GUN 001-005, 155-157, 201-999
POST SB 737-27-1253
27-21-00
Config 2
Page 552
Oct 10/2007
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
1) Push on the adapter, SPL-1681 until the rudder starts to move.
2) Multiply the compression gage value on the adapter, SPL-1681 by a multiplication
factor given in (Table 503):
NOTE: The angle from the horizontal value is also shown on the adapter, SPL-1681.
Table 503/27-21-00-993-816-002
Angle from Horizontal Multiplication Factor
08 1.0
58 1.0
108 0.98
158 0.97
　
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-600/700/800/900 AIRCRAFT MAINTENANCE MANUAL飛機維護手冊2(67)