曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

You can set this values to your needs in the range of 300 – 1600.
The controlled Offset is 5616 Bit3, e.g. for pmSounds use
nsteersound, 5616, .3, 1, cyc, 100
But in pmSounds there is no sound available, you need to create one or use some sound file that fulfills your
needs.
Steer.ini
[Steer Angle]
7 kts =1600
8 kts =1600
9 kts =1550
10 kts =1350
11 kts =1350
...
29 kts =950
30 kts =950
31 kts =950
32 kts =900
33 kts =850
34 kts =800
35 kts =750
www.technicalservicerichter.com Page 21
Project Magenta – MCP settings
If you use AutoBrake II together with Project Magenta’s MCP, make sure you set the following in MCP.ini
file.
DisableAutobrakes = Off
DisableBrakes = On
You will find the MCP.ini file in your MCP main folder.
www.technicalservicerichter.com Page 22
TSR Autobrake Pro Airbus
It contains
 3 Position Autobrake System for Airbus
LOW / MED / MAX / (OFF)
 Brake distance variables on weather factor (Rain, Snow and its heaviness), automatic setting by FS9 / FSX
or manual by e.g. Project Magenta pmInstructor
 Slippery RWY (vulnerable to weather conditions) effects as skidding to A/C in Braking Phase
 RWY resistance on Takeoff (vulnerable to weather conditions), Rain; Slush; …
 Displaying of used Landing Distance, as well displayable on Project Magenta pmInstructor
 Self recognition of Project Magenta pmSystems and using of its Hydraulic system for charging the
Brakeaccu, without pmSystems the Hydraulic pressure is simulated
 Spoiler ARM control for ground handling
 Full Flaps Control, 0  1  2. For correct indication of 1 / 1+F
 Brake Sound control, can control a sound for braking with e.g. pmSounds
 Steering Sound control, can control a sound for steer scrubbing with e.g. pmSounds
www.technicalservicerichter.com Page 23
Settings
 NO Differential Brake, sets the left and right pedal as only one pedal input, is also used for Joystick-
Button input if no Pedals are available
 NO Analog Toe Brakes, Your hardware works not analog OR you would like to use the build-in DBS
(Dynamic Brake System) instead of your analog hardware. The setting is also used for Joystick-Button
input if no Pedals are available
 WXR Manually Set, if unchecked the FS weather will set the RWY conditions. If checked you can set the
RWY conditions by e.g. Project Magenta pmInstructor
 Sound Output 0 - 100, if checked you will get a Offset output value for e.g. sound programs that can
handle with this value the loudness of a Braking Sound. If it is unchecked it just gives the value 0 for
NONE braking and value 1 for braking.
 Press High, sets the high press value for the pushed Toe Brake Pedal in DBS mode
 Press Low, sets the low press value for the non pushed Toe Brake Pedal
 Base ft/s^2, sets the base negative acceleration rate in DBS mode
www.technicalservicerichter.com Page 24
Display I
WXR Condition
Current weather conditions in FS
 DRY
 WET
 WET 6mm
 SLUSH 6mm
 SLUSH 13mm
 SNOW 5cm
 ICE
RWY Condition
Current runway conditions, did you put by FS or by the Instructor station.
 DRY
 WET
 WET 6mm
 SLUSH 6mm
 SLUSH 13mm
 SNOW 5cm
 ICE
Brake Pressure
Displays the brake pressure in psi, is as well available by an Offset (see Offset list below)
Landing Distance
Displays the used Landing Distance in ft, is as well available by an Offset (see Offset list below)
www.technicalservicerichter.com Page 25
Display II
ANTISKID INOP
Antiskid Inop indication is as well available by an Offset (see Offset list below)
Brakeaccu Press
The Brakeaccu value 0-520 reflects to the pressure 0-3000psi.
The value is readable in Offset 0x579E, 2 Byte lengths, very useful for gauges like the Brake Press Gauge
from Flight Illusion or others.
The displayed are NOT static because they will change on each braking phase.
The charging of Brakeaccu is done by the running engine or by pmSystems by Project Magenta and its
Hydraulic pressure values (pmSystems is self recognized).
Left Brake / Right Brake
It shows the actually brake pressure as bar, for left and right brakes. The value 0-520 reflects to the pressure
0-3000psi in Offset 0x6DC6, 2 Byte length (Left), and Offset 0x6DC8, 2 Byte length (Right).
Auto Brake Switch
It reflects just the actually position of the Autobrake switch, RTO / OFF / ...
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：航空資料17(95)