曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

ntoolowflaps1, 7930, .3, 1, on
nglideslope1, 7930, .4, 1, on
nwindshear1, 7930, .5, 1, on
npullup1, 7930, .6, 1, on
- go to Sounds subfolder in pmSounds main folder
- search and change the following existing sound files names (.wav)
FROM TO
ntowarn  ntowarn1
ntoolowgear  ntoolowgear1
ntoolowflaps  ntoolowflaps1
ntoolowterrain  ntoolowterrain1
nglideslope  nglideslope1
- Copy nwindshear.wav and paste in the same folder (your drive\pmSounds\sounds\)
- Rename this file to nwindshear1.wav
- Copy npullup.wav and paste in the same folder (your drive\pmSounds\sounds\)
- Rename this file to npullup1.wav
For nbrakesound and nsteeringsound you need to add a sound file (wav) to sounds folder
because this sound files doesn’t exists.
www.technicalservicerichter.com Page 69
pmSystems changes
This is for AutoBrake Pro ONLY, NOT needed for TSR Boeing 737-NG !
Just add this Offsets to sysvar.txt of pmSystems.
6DB1 1 TsrAb
and this lines to Logic section (somewhere below [Logics])
DisableGCMessages = 1
setmessage '4 Less BRAKEACCU' brakeaccu < 200
setmessage '4 Auto Brake RTO' (TsrAb = 0)
setmessage '4 Auto Brake OFF' (TsrAb = 1)
setmessage '4 Auto Brake 1' (TsrAb = 2)
setmessage '4 Auto Brake 2' (TsrAb = 3)
setmessage '4 Auto Brake 3' (TsrAb = 4)
setmessage '4 Auto Brake MAX' (TsrAb = 5)
But DON'T change the message text to "Autobrake" instead of the "Auto Brake"
Bleed / Pack System
If Bleed / Pack System is enabled you need to remove the following lines from your logic file, e.g.
pmsys737.lgc
!! BUT DON’T REMOVE THIS BOTH LINES !!
off = 0
on = 1
This lines needs to be removed.
if (apumode = 3) and apubleed
if (fsStarter1 = 1) or (fsStarter2 = 1)
bl5 = 30
else
bl5 = 20
endif
else
bl5 = 0
endif
if eng1bleed and (fs1n1 > 12)
bl1 = 26
else
bl1 = bl5
endif
if eng2bleed and (fs2n1 > 12)
bl2 = 26
else
bl2 = 0
endif
if isolationvalve > 0
if (bl1 > bl2) or (bl1 = bl2)
b1r = bl1
endif
if (bl2 > bl1) or (bl2 = bl1)
b1r = bl2
endif
b2r = b1r
else
www.technicalservicerichter.com Page 70
b2r = bl2
b1r = bl1
endif
if (FlapsPosL > 0) or FSonGround
Ramvalve = 1
else
Ramvalve = 0
endif
if b1r
if pack1
b1r = b1r - (2 * pack1)
ramair = Ramvalve [1]
else
ramair = 0
endif
else
ramair = 0
endif
if b2r
if pack2
b2r = b2r - (2 * pack2)
ramairr = Ramvalve [1]
else
ramairr = 0
endif
else
ramairr = 0
endif
if batt1 = 0
b1r =0
b2r =0
endif
dualbleed = (apubleed and eng1bleed)
if dualbleed = 0
dualbleed = (isolationvalve and (apubleed and eng2bleed))
endif
if pwr
bleedpsi1 = counter b1r 15
bleedpsi2 = counter b2r 15
bleed1ref = b1r
bleed2ref = b2r
endif
GC - Dimm / Bus-Click
If BusClick is enabled you need to remove the following lines from your logic file, e.g. pmsys737.lgc
if not pwr
pmCaptPFDInop = 1
pmCaptNDInop = 1 [.5]
pmFONDInop = 1 [.7]
pmFOPFDInop = 1 [.3]
pmSD1Inop=1 [.7]
pmSD2Inop=1 [.7]
pmCDUInop=1
pmRCDUInop=1
pmStandByInop=1
pmAPInop = 1
else
pmCaptPFDInop = 0
pmCaptNDInop = 0
pmFONDInop = 0
pmFOPFDInop = 0
pmSD1Inop=0
pmSD2Inop=0
pmCDUInop=0 [1]
pmRCDUInop=0 [3]
pmStandByInop=0 [2]
pmAPInop = 0
endif
Technical Training
Detailed Course Descriptions
A330 (PW 4000)
A330 (PW 4000), T1: Part-66 Cat. B1, Line & Base Maintenance............................................. 2
A330 (PW 4000), T2: Part-66 Cat. B2, Line & Base Maintenance............................................. 3
A330 (PW 4000), T1/T2: Part-66 Cat. B1/B2, Line & Base Maintenance .................................. 4
A330 (PW 4000), T3: Part-66 Cat. A, Ramp & Transit............................................................... 5
A330 (PW 4000), T4: Part-66 Cat. C, General Familiarization................................................... 6
A330 (PW4000) vs. A340 (CFM56), T1/T2: Part-66 Cat. B1/B2, Line & Base Maintenance ..... 7
Course Descriptions A330 (PW 4000)
A330 (PW 4000), T1: Part-66 Cat. B1, Line & Base Maintenance
Electrical Systems, Airframe & Powerplant – ATA Spec 104 Level 3
Avionics Systems – ATA Spec 104 Level 2
Duration: 30 days / 210 lessons theoretical training
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：航空資料17(107)