NOSE GEAR CENTERED
PIN NS-5 CAUTION
SUMMING LEVER
DO NOT TURN
OR HOLD TILLER WHILE TOWING AIRPLANE
MECHANISM
CONNECTING
FWD
ROD D
1 LEFT SIDE TILLER - NWS1A-1 CROSSES
C
NWS1A-2 ON THE OUTBOARD SIDE RIGHT SIDE TILLER - NWS1B-2 CROSSES NWS1B-1 ON THE OUTBOARD SIDE
Nose Wheel Steering System Rigging
Figure 502 (Sheet 2)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
32-51-00
ALL ú ú 01 Page 507 ú Jun 10/97
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
NOSE WHEEL STEERING RIG LOADS
100
90
80
70
(POUNDS) LOAD RIGGING 50 60
40
30
20
-40 -20 0 20 40 60 80 100 120 140 160
AMBIENT TEMPERATURE (`F)
Nose Wheel Steering System Rigging Figure 502 (Sheet 3)
U23300
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
32-51-00
ALL ú ú 02 Page 508 ú Jun 10/90
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
SEE A
B
B
A
A
FWD
A
5.5
UPPER
TORSION CRIMP FERRULE
CABLE LINK (2 PLACES)
BUTTON
QUICK- 14.0
RELEASE
PIN
APEX 0.12
BOLT
2.12
LOWER THREADED
TORSION BUSHING
LINK NOTE:____ DIMENSIONS ARE IN INCHES.
HANDLE
A-A B-B
Torsion Links Installation
Figure 503
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
32-51-00
ALL ú ú 02 Page 509 ú Jun 10/90
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
(d) Pin NS-4 in the cable compensator, located in the bay aft of
the nose wheel well bulkhead (Fig. 502).
1) Adjust the length of cables NWS1A and NWS1B, if it is
necessary, so that the pin may be put in.
NOTE:____ The rigging pin must go through the housing and
engage both cable drums.
(e) Pin NS-5 in the summing lever in the nose gear shock strut.
1) Adjust the length of cables NWS2A and NWS2B, if it is
necessary, so that the pin may be put in.
NOTE:____ The rigging pin must engage the structure on
both sides.
(f) Pin NS-6 in the metering valve input arm on the nose gear shock
strut
1) Adjust the length of the connecting rod (Fig. 502), if it
is necessary, so that the pin may be put in.
(g) The rudder rigging pin R-3 (No. 3 pin of rudder system) in the
rudder quadrant under the flight deck floor (AMM 27-21-00/501)
S 825-013
(6)
Align the nose gear wheel vertical plane within | 1/4 degree of the airplane centerline.
S 835-014
(7)
Adjust the steering rod (Fig. 501) length so that the attaching bolts fit freely, and then install the rod.
S 715-015
(8)
Make sure that rigging pin NS-3 is loose, but do not remove it.
S 835-016
(9)
Adjust the length of the connecting rod (Fig. 502), so that rigging pins NS-5 and NS-6 are loose, and connect it to the metering valve input arm.
(a)
Do not remove the rig pin.
S 835-017
(10)
AIRPLANES WITH NEW CABLES; Tighten NWS1A/NWS1B and NWS2A/NWS2B cables to 120.00 (| 10) pounds.
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 起落架 LANDING GEAR 7(183)
