NEW TIRE (REF)  NEW TIRE (REF)

TIRE SHOULD BE REMOVED IF BLISTERS OR CRACKS ARE FOUND IN A GROOVE BOTTOM WHICH EXPOSES FABRIC
SHOULDER WEAR CONDITIONS

Tire Damage/Wear Conditions
Figure 602 (Sheet 8)

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-45-04
 ALL  ú ú 04 Page 611 ú Oct 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 S 216-008
 (4)  
Examine the wheels for melted, pushed out or leaking thermal fuses (AMM 32-45-03/601).

 (a)  
The tire is not serviceable if it was deflated by a thermal fuse that is melted or pushed out.

 (b)  
When you remove the tire/wheel, attach a tag with the cause of removal on the wheel.

 (c)  
Examine the wheel for heat damage. Refer to the applicable vendor maintenance manual.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-45-04
 ALL  ú ú 03 Page 612 ú Oct 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 NOSE GEAR WHEEL SNUBBER - MAINTENANCE PRACTICES
_______________________________________________
 1.  General
_______
 A.  This procedure contains the instructions to remove and install the wheel snubber assemblies, and to examine them for wear. A snubber assembly contains a spring and a brake shoe.
 B.  Two wheel snubbers are installed on the top panel assembly of the nose gear wheel well. One snubber is used for each wheel.
 TASK 32-45-05-022-006
 2.  Nose Wheel Snubber Assembly - Removal
_____________________________________
 A.  References
 (1)  
AMM 09-11-00/201, Towing

 (2)  
AMM32-00-30/201, Landing Gear Door Locks

 (3)  
IPC 32-45-05, Fig. 1

 B.  
Access

 (1)  
Location Zone
 113 Nose Gear Wheel Well, LH
 114 Nose Gear Wheel Well, RH

 C.  
Procedure (Fig. 201)

 S 212-009
 (1)  Make sure the ground locks are installed in all landing gear (AMM 09-11-00/201).
 S 862-001
 WARNING: YOU MUST CAREFULLY DO THE STEPS IN THE TASK BELOW TO INSTALL
_______ THE DOOR LOCKS ON THE LANDING GEAR DOORS. THE DOORS CAN CLOSE QUICKLY IF YOU DO NOT INSTALL THE DOOR LOCKS CORRECTLY. THIS CAN CAUSE INJURY TO PERSONS OR DAMAGE TO EQUIPMENT.
 (2)  Do this task: "Installation of the Door Locks on the Nose Landing Gear" (AMM 32-00-30/201).
 S 032-007
 WARNING: THE NOSE WHEEL SNUBBER BLOCKS CONTAIN FIBERS OR DUST WHICH CAN
_______ BE HARMFUL IF INHALED. MAKE SURE YOU PUT ON A PROTECTIVE TYPE RESPIRATOR WHEN YOU DO WORK NEAR THE SNUBBER BLOCKS THAT CAN CAUSE AIRBORNE FIBERS OR DUST.
 (3)  
Hold the snubber assembly and remove the bolts that attach the assembly to the top of the wheel well.

 (4)  
Remove the snubber assembly.

 S 032-011

 (5)  
If it is necessary, disconnect the nuts and bolts (12 locations) to remove the snubber blocks from the spring.

 S 022-010
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-45-05
 ALL  ú ú 01 Page 201 ú Oct 10/97
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 747-400 MAINTENANCE MANUAL
WHEEL SNUBBER SEE A
(2 LOCATIONS) 0.205 |0.002 DIA HOLE 0.62-0.64 O.D. SPOTFACE 0.06-0.09 R FILLET 
B SPOTFACE 
YDMM-32-45-0029 
TOP PANEL  SNUBBER ASSEMBLY  BOLTS (4 LOCATIONS) 
FWD 
0.20 DEPTH  SPOTFACE |0.01 R COUNTERBORE NUT BSEE 0.205 |0.002 DIA HOLE (10 LOCATIONS) SNUBBER BLOCK INCH0.17 0.14 0.688-0.708 x 0.04 BOLTS 15.35 |0.25 INCHES (12 LOCATIONS) 
A WHEEL SNUBBER 
Figure 201 Nose Gear Wheel Snubber 
　
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機(jī)維護(hù)手冊 起落架 LANDING GEAR 7(154)