(f)  
Push the LSK that is adjacent to <32 BRAKE CONTROL to show the GROUND TESTS menu for the brake control system.

 NOTE: If INHIBITED shows above <BRAKE RELEASE, the test
____
 will not operate.

 (g)  If INHIBITED shows above <BRAKE RELEASE: 1) Push the LSK that is adjacent to the test prompt. 2) Do the steps shown on the CDU. 3) Push the LSK that is adjacent to <RETURN to show the ground
 tests menu again.
 G. Brake Release Ground Test
 S 745-205
 (1)  
Push the LSK that is adjacent to <BRAKE RELEASE.

 S 745-210

 (2)  
Push the START TEST> LSK after the instructions of the TEST PRECONDITIONS screens are complete. The CDU will then show the first of three menus for the Brake Release Test.

 S 745-290

 (3)  
Do these steps to complete the Brake Release Test at each of the sixteen wheel locations:

 (a)  
Look at the pressure gage at a brake to monitor the pressure at the brake.

 (b)  
Push the LSK related to this brake, to start the Brake Release Test for this brake.

 (c)  
The results of the test are satisfactory if the pressure at the brake during the test is as follows: 1) The pressure at the brake at the start of the test is equal

 to system pressure (|200 psig).
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-42-00
 ALL  ú ú 04 Page 510 ú Oct 10/96
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 2)  The pressure at the brake decreases to 200 psig or less for approximately 6 seconds.
 NOTE: At this time, the CDU will show the message VERIFY
____ BRAKE NUMBER X IS RELEASED (X is equal to 1 thru 16 as applicable).
 3)  The pressure at the brake increases again to system pressure (|200 psig), and stays at this value.
 H.  Put the Airplane Back to Its Usual Condition
 S 845-311
 (1)  Remove pressure from the brakes:
 NOTE: If you manually supplied pressure during the test,
____ release the brake pedals to remove pressure from the brakes.
 (a)  
Release the parking brake.

 (b)  
Close this circuit breaker on the P6 panel:
 1) 6L18, PARK BRAKE

 S 845-406
 (2)  
Push the LSK that is adjacent to <RETURN until the GROUND TESTS menu shows.

 S 845-415

 (3)  
Make sure that DONE shows adjacent to <BRAKE RELEASE.

 S 845-405

 (4)  
Remove power from hydraulic systems No. 1, 2 and 4
 (AMM 29-11-00/201).

 S 085-315

 (5)  
Remove the pressure gage and install a brake bleeder assembly at each brake unit (16 locations):

 (a)  
Make sure that the parking brake is released.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-42-00
 ALL  ú ú 07 Page 511 ú Feb 10/97
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 (b) Make sure that the brakes are not operated manually.
 WARNING:_______ THE BRAKES MUST NOT BE IN OPERATION WHEN YOU CONNECT OR
 DISCONNECT THE TWO PARTS OF A HYDRAULIC BRAKE DISCONNECT.
 IF YOU TRY TO CONNECT OR DISCONNECT A HYDRAULIC BRAKE
 DISCONNECT WITH THE BRAKE IN OPERATION, HYDRAULIC FLUID
 UNDER HIGH PRESSURE CAN RELEASE.  THIS CAN CAUSE INJURY TO

 PERSONNEL AND DAMAGE TO EQUIPMENT.
 (c)  
To remove all pressure from the brake, disconnect the hose half of the hydraulic brake disconnect from the brake half.

 (d)  
Remove the pressure gage from the brake unit housing.

 (e)  
Do these steps to install a brake bleeder assembly on the brake unit housing:

 NOTE: Each brake bleeder assembly has a bleeder valve
____ installed in an adapter. The adapter is installed in the brake unit housing.
 CAUTION: TIGHTEN THE ADAPTER TO 90-110 POUND-INCHES.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 起落架 LANDING GEAR 7(13)