32-45-03
ALL ú ú 01 Page 801 ú Oct 10/97
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
AXLE SLEEVE (SIDE VIEW)
AXLE SLEEVE (EXAMPLE)
(END VIEW)
(EXAMPLE)
____ ALL DIMENSIONS ARE IN INCHES
NOTE:
EACH BLEND (SQUARE INCHES)
THE SUM OF BLENDED AREAS MAY NOT
BE MORE THAN 50% OF THE AVAILABLE SURFACE AREA
Repair Limits for the Axle Sleeve
Figure 801
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
32-45-03
ALL ú
ú 01 Page 802
ú Oct 10/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
S 358-006
(4)
Remove the file marks with an abrasive cloth.
S 648-007
(5)
Apply grease to the repaired areas.
F.
Repair Axle Sleeve Cracks
NOTE: One crack for each journal area, that starts in the area between
____ the bearing journals, is permitted if the condition that follows is obeyed:
-The crack does not extend more than 1/4 inch into the journal area.
S 038-011
CAUTION:_______REMOVE THE AXLE SLEEVE BEFORE YOU DRILL IT. IF YOU DO NOT REMOVE THE AXLE SLEEVE, YOU CAN CAUSE DAMAGE TO THE AXLE.
(1)
Remove the axle sleeve from the landing gear axle
(AMM 32-11-32/401 and AMM 32-13-26/401).
S 358-008
(2)
Do the steps that follow to repair the bearing journal areas:
(a)
Drill a 1/4 inch hole on each end of the crack.
NOTE: The center of the hole must be at the end of the crack.
____
(b)
Use a file to make the crack into a slot that is 1/32 inch minimum to 1/16 maximum in width.
(c)
Break the sharp edges to 0.030 inch radius.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
32-45-03
ALL ú ú 01 Page 803 ú Oct 10/97
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
TIRES - INSPECTION/CHECK
________________________
1. General_______
A. This procedure contains the task to do an inspection/check of the landing gear tires. The tires are examined to make sure if they are in good condition for safe operation and minimum airplane maintenance.
B. If the tires have flat spots or are blown because of a locked wheel slide (not a tire structural failure) refer to AMM 05-51-25/201 to find the cause.
TASK 32-45-04-206-011
2. Examine the Tires_________________
A. References
(1)
AMM 09-11-00/201, Towing
(2)
AMM 12-15-06/301, Servicing
(3)
AMM 32-00-30/201, Landing Gear Door Locks
(4)
AMM 32-45-01/401, Main Gear Tire/Wheel
(5)
AMM 32-45-02/401, Nose Gear Tire/Wheel
(6)
AMM 32-45-03/601, Wheel
(7)
AIPC 32-45-01 Fig. 2, AIPC 32-45-02 Fig. 1
B.
Access
(1)
Location Zones
715 Nose Landing Gear
755 Body Landing Gear, LH
765 Body Landing Gear, RH
735 Wing Landing Gear, LH
745 Wing Landing Gear, RH
C.
Prepare to Examine the Tires
S 496-001
(1) Make sure that the landing gear ground locks are installed (AMM 09-11-00/201).
S 496-002
WARNING: REFER TO SPECIFIED PROCEDURE TO INSTALL THE DOOR LOCKS
_______ CORRECTLY. THE DOORS CAN CLOSE QUICKLY IF YOU INSTALL THE DOOR LOCKS INCORRECTLY. THIS CAN CAUSE INJURIES TO PERSONS AND DAMAGE TO THE EQUIPMENT.
(2)
Install the door locks for the main gear (AMM 32-00-30/201).
S 616-003
(3)
Make sure the tire is inflated to the correct pressure (AMM 12-15-06/301).
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 起落架 LANDING GEAR 7(151)
