32-46-00
 ALL  ú ú 12 Page 506 ú Jun 10/92
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 (f)  
Use the ST2584C wrench to connect the disconnected sensor.

 (g)  
Tighten the coupling nut on the sensor connector to 55-65 pound- inches.

 (h)  
Make sure the EICAS synoptic display shows a brake temperature indication for all wheel positions.

 (i)  
Do the same steps again for the sensors at the remaining wheel positions. 1) Use the PREVIOUS PAGE key on the control display unit to

 see the EXISTING FAULTS indication for each subsequent sensor.

 (j)  
After you do the test for the 16 temperature sensors, make sure there are no EXISTING FAULTS for the BTMS.

 H.
Put the Airplane Back to Its Usual Condition

 S 865-015
 (1) Remove the electrical power if it is necessary (AMM 24-22-00/201).
 S 095-049
 WARNING: YOU MUST CAREFULLY DO THE STEPS IN THE TASK BELOW TO REMOVE THE
_______ DOOR LOCKS FROM THE LANDING GEAR DOORS. THE DOORS CAN CLOSE QUICKLY IF YOU DO NOT REMOVE THE DOOR LOCKS CORRECTLY. THIS CAN CAUSE INJURY TO PERSONS OR DAMAGE TO EQUIPMENT.
 (2)  
Do this task: "Removal of the Door Locks from the Wing Landing Gear" (AMM 32-00-30/201).

 S 095-050

 (3)  
Do this task: "Removal of the Door Locks from the Body Landing Gear" (AMM 32-00-30/201).

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-46-00
 ALL  ú ú 05 Page 507 ú Jun 10/97
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 BRAKE TEMPERATURE SENSOR - REMOVAL/INSTALLATION
_______________________________________________
 1.  General_______
 A.  This airplane uses sixteen brake temperature sensors. Each main wheel location has one sensor. All the brake temperature sensors are the same and are removed and installed in this procedure.
 B.  Remove the brake temperature sensor when the Central Maintenance Computer isolates a fault to a failed temperature sensor.
 TASK 32-46-01-024-011
 2.  Brake Temperature Sensor - Removal__________________________________
 A.  Special Tools and Equipment
 (1)  
ST2584C - Plier

 (2)  
PWA 85749 - Plier, alternate tool

 B.  
References

 (1)  
AMM 09-11-00/201, Towing

 (2)  
AMM 32-00-30/201, Landing Gear Door Locks

 (3)  
IPC 32-46-01 Fig. 1

 (4)  
SSM 32-46-01

 (5)  
WDM 32-46-11, WDM 32-46-12

 C.  
Access

 (1)  
Location Zones 118 Electrical & Electronics Compartment, RH

 (P180 DC Power Distribution Panel) 755 Body Landing Gear - Left 765 Body Landing Gear - Right 735 Wing Landing Gear - Left 745 Wing Landing Gear - Right
 D.  Procedure (Fig. 401)
 S 864-001
 (1)  Make sure that the ground locks are installed in all landing gear (AMM 09-11-00/201).
 S 494-002
 WARNING:  YOU MUST CAREFULLY DO THE STEPS IN THE TASK BELOW TO INSTALL
_______ THE DOOR LOCKS ON THE LANDING GEAR DOORS. THE DOORS CAN CLOSE QUICKLY IF YOU DO NOT INSTALL THE DOOR LOCKS CORRECTLY. THIS CAN CAUSE INJURY TO PERSONS OR DAMAGE TO EQUIPMENT.
 (2)  Do this task: "Installation of the Door Locks on the Body Landing Gear" (AMM 32-00-30/201).
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-46-01
 ALL  ú ú 01 Page 401 ú Jun 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A

747-400
MAINTENANCE MANUAL

FWD 
SEE A SENSOR BRAKE TEMPERATURE 
(2 LOCATIONS) WASHER  BSEE TEMPERATURE SENSOR BRAKE AXLE 
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 起落架 LANDING GEAR 7(164)