S 494-036

 (3)  
Do this task: "Installation of the Door Locks on the Wing Landing Gear" (AMM 32-00-30/201).

 S 494-037

 (4)  
Do this task: "Installation of the Door Locks on the Body Landing Gear" (AMM 32-00-30/201).

 S 584-004

 (5)  
Lift the axle with a jack until the tire is clear from the ground (AMM 07-11-03/201).

 S 684-005
 WARNING: DEFLATE THE TIRE BEFORE YOU DO THE PROCEDURE THAT FOLLOWS.
_______ FAILURE TO DEFLATE THE TIRE CAN CAUSE INJURY TO PERSONS IF AN ACCIDENTAL TIRE EXPLOSION OCCURS.
 (6)  Deflate the tire with a tire deflation tool.
 S 684-007
 WARNING: DO NOT APPLY TOO MUCH FORCE TO THE VALVE STEM WHEN YOU DEFLATE
_______ THE TIRE. TOO MUCH FORCE CAN CAUSE DAMAGE TO THE VALVE CORE. KEEP PERSONS AWAY FROM THE VALVE DURING THE VALVE ASSEMBLY REMOVAL. THE VALVE ASSEMBLY CAN BLOW OFF ACCIDENTALLY AND CAUSE INJURY TO PERSONS.
 (7)  
If you think there is damage to the valve core, such that you cannot deflate the tire with a deflation tool, do these steps:

 (a)  
Slowly turn the valve assembly counterclockwise to loosen the valve assembly, until gas starts to leak through the boss.

 (b)  
At the same time, push in lightly on the valve stem.

 (c)  
Do not try to remove the valve assembly until you remove all the pressure from the tire.

 S 024-009
 (8)  
Remove the tire inflation valve with these steps:

 (a)  
Turn the valve counterclockwise until you can pull it from the wheel.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-45-08
 ALL  ú ú 01 Page 403 ú Oct 10/97
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 (b)  Remove the grommet.
 TASK 32-45-08-424-013
 3. Tire Inflation Valve - Installation
___________________________________
 A. Consumable Materials
 (1)  
D00378 Grease Aeroshell 22 (preferred)

 (2)  
D00165 Grease - Mobil 28, (optional)

 (3)  
D50005 Mobil Aviation Grease SHC 100 (optional)

 B.
References

 (1)  
AMM 07-11-03/201, Jacking Airplane Axles

 (2)  
AMM 09-11-00/201, Towing

 (3)  
AMM 12-15-06/301, Landing Gear Tire Servicing

 (4)  
AMM 32-00-30/201, Landing Gear Door Locks

 (5)  
AIPC 32-45-08, Fig. 1

 C.
Access

 (1)  
Location Zone
 715 Nose landing gear
 735 Wing landing gear - LH
 745 Wing landing gear - RH
 755 Body landing gear - LH
 765 Body landing gear - RH

 D.
Procedure (Fig. 401)

 S 424-014
 (1)  
Install the inflation valve with these steps:

 (a)  
Install the grommet on the tire valve assembly.

 (b)  
Install the valve through the opening of the outer-wheel-half wed, into the threaded port of the inner-wheel-half.

 NOTE: To prevent leaks, make sure the grommet is seated in the
____
 hole.

 (c)  
Tighten the inflation valve to 175 pound-inches dry torque.

 (d)  
Install a lockwire.

 (2)
Inflate the tire to the correct pressure (AMM 12-15-06/301).

 (3)
Make sure there is no leakage through the inflation valve.

 (4)  
Lower the wheels and remove the jacks (AMM 07-11-03/201).

 S 614-018
 S 284-019
 S 584-020
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-45-08
 ALL  ú ú 01 Page 404 ú Oct 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 S 094-021
 WARNING: YOU MUST CAREFULLY DO THE STEPS IN THE TASKS BELOW TO REMOVE
_______ THE DOOR LOCKS ON THE LANDING GEAR DOORS. THE DOORS CAN CLOSE QUICKLY IF YOU DO NOT INSTALL THE DOOR LOCKS CORRECTLY. THIS CAN CAUSE INJURY TO PERSONS OR DAMAGE TO EQUIPMENT.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 起落架 LANDING GEAR 7(157)