bearing assembly (11) to the structure. 2) Install six screws (3), washers (10) and nuts (9).

 (c)  
Install the nuts (2) on each end of the torque tube
 assembly (8).

 (d)  
Connect the pushrod (6) to the lever on the inboard side of the torque tube assembly (8) with the screw (7), washer (5), and nut (4).

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-44-02
 ALL  ú ú 03 Page 405 ú Feb 10/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

 (e)  Install the spring (12) to the bracket on the structure and to the flange on the bottom of the inboard pawl.
 (3)  S 824-011Adjust the parking brake linkage (AMM 32-44-00/501).
 (4)  S 414-010Install the ceiling panels (AMM 25-22-01/401).

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-44-02
 ALL  ú ú 03 Page 406 ú Oct 10/97
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 PARKING BRAKE MODULE - REMOVAL/INSTALLATION
___________________________________________
 1.  General
_______
 A.  This procedure contains two tasks:
 (1)
The removal of the parking brake module

 (2)
The installation of the parking brake module.

 B.  
The parking brake module is connected to the brake return line of the normal brake system. The parking brake module is installed on the keel beam in the wheel well for the right body landing gear. The electric motor stays on the module during the removal and the installation. For a removal/installation of the electric motor AMM 32-44-08/401.

 TASK 32-44-04-024-008
 2.  Removal of the Parking Brake Module (Fig. 401)
___________________________________
 A.  References
 (1)
AMM 09-11-00/201, Towing

 (2)
AMM 24-22-00/201, Manual Control

 (3)
AMM 29-11-00/201, Main Hydrualic Supply System

 (4)
AMM 32-00-30/201, Landing Gear Door Locks

 (5)
IPC 32-44-04 Fig. 1

 (6)
SSM 32-44-01

 (7)
WDM 32-44-11

 B.  
Access

 (1)  
Location Zones
 138 Body Landing Gear Well - Right
 221 Control Cabin, L.H.
 222 Control Cabin, R.H.

 C.  
Prepare for the Removal

 S 494-018
 WARNING: YOU MUST CAREFULLY INSTALL THE GROUND LOCKS IN ALL LANDING
_______ GEAR. AN ACCIDENTAL RETRACTION OF THE LANDING GEAR CAN CAUSE INJURY TO PERSONS AND DAMAGE TO EQUIPMENT.
 (1) Install the ground locks in all landing gear (AMM 09-11-00/201).
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-44-04
 ALL  ú ú 01 Page 401 ú Oct 10/97
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

ADAPTER 
(3 LOCATIONS) 
WASHER 
(4 LOCATIONS) 
O-RING 
SEE  A  (6 LOCATIONS) 
NUT  BACKUP RING 
(4 LOCATIONS)  (3 LOCATIONS) 

HYDRAULIC LINES 
(3 LOCATIONS) 
PARKING 
BRAKE 
MODULE  BOLT 
(4 LOCATIONS) 
(4 LOCATIONS) WASHER  (3 LOCATIONS) ADAPTER  CONNECTOR ELECTRICAL 
A  1
O-RING 
(6 LOCATIONS) 
NUT  BACKUP RING 
(4 LOCATIONS)  (3 LOCATIONS) 

(3 LOCATIONS) HYDRAULIC LINES  1  RELIEF VALVE NOT INSTALLED INTERNAL THERMAL RELIEF VALVE, PARKING BRAKE MODULES WITH 
PARKING  ON ALL AIRPLANES 
BRAKE  2  PARKING BRAKE MODULES WITH 
MODULE  BOLT  EXTERNAL THERMAL RELIEF VALVE 
(4 LOCATIONS) 
ELECTRICAL 
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 起落架 LANDING GEAR 7(120)