OUTBD
FWD
1 POINT
1 CAUTION: THE GREASE GUN MUST NOT EXCEED 400 PSI WHEN YOU
A
LUBRICATE THE MAIN GEAR TRUNNION BEARING. HIGHER RESSSURE MAY CAUSE STRUCTURE DAMAGE.
2 MIL-G-21164 OR MIL-G-3827 IS OPTIONAL TO BMS 3-33
Landing Gear Support Beam Lubrication Figure 301
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 12-25-07
 ALL  ú ú 03 Page 301 ú Nov 12/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 AFT ENTRY DOOR LUBRICATION
__________________________
 1.  General_______
 A. This procedure contains two tasks:
 (1)  
The lubrication of the aft entry door.

 (2)  
The lubrication of the handle on the aft entry door.

 TASK 12-25-11-603-001
 2.  Aft Entry Door Lubrication__________________________
 A. Special Tools and Equipment
 (1)  Lubrication Set - Entry, Cargo, Service and Galley Door Camshaft Bearings - F72942-1
 NOTE: Use the set to lubricate fittings where access is not easy.
____
 (2)  Maintenance Stand
 B. Standard Tools and Equipment
 (1)  
Flush gun (grease gun)

 (2)  
Oil squirt can

 C. Consumable Materials
 (1)  
D00013 Grease - MIL-G-23827

 (2)  
D00091 Oil - MIL-L-7870

 D. References
 (1)  
AMM 25-61-35/201, Escape Slide Assembly (Door Mounted)

 (2)  
AMM 52-13-21/401, Aft Entry Door Lining and Insulation

 E. Access
 (1)  
Location Zone
 110 Aft Entry Door

 (2)  
Access Panel
 4601L Aft Entry Door

 F. Procedure
 S 843-007
 (1)  Prepare to lubricate the door.
 (a)
Remove the escape slide assembly (AMM 25-61-35/201).

 (b)
Remove the lining from the door (AMM 52-13-21/401).

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 12-25-11
 ALL  ú ú 01 Page 301 ú Mar 15/94
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 (c)  
Remove the lining from the gates.

 (d)  
Remove the plate from the handle mechanism.

 S 643-006
 (2)  
Lubricate the door (Fig. 301).

 S 843-008

 (3)  
Put the door in a serviceable condition.

 (a)  
Install the plate on the handle mechanism.

 (b)  
Install the linings on the gates.

 (c)  
Install the lining on the door (AMM 52-13-21/401).

 (d)  
Install the escape slide assembly on the door (AMM 25-61-35/201).

 TASK 12-25-11-603-005
 3.  Aft Entry Door Handle Mechanism Lubrication___________________________________________
 A. Special Tools and Equipment
 (1)  Lubrication Set - Entry, Cargo, Service and Galley Door Camshaft Bearings - F72942-1
 NOTE: Use the set to lubricate fittings where access is not easy.
____
 (2)  Maintenance Stand
 B. Standard Tools and Equipment
 (1)  Flush gun (grease gun)
 C. Consumable Materials
 (1)  D00013 Grease - MIL-G-23827
 D. References
 (1)  
AMM 25-61-35/201, Escape Slide Assembly (Door Mounted)

 (2)  
AMM 52-13-21/401, Aft Entry Door Lining and Insulation

 E. Access
 (1)  
Location Zone
 110 Aft Entry Door

 (2)  
Access Panel
 4601L Aft Entry Door

 F. Procedure
 S 843-009
 (1)  
Prepare to lubricate the door.

 (a)  
Remove the escape slide assembly (AMM 25-61-35/201).

 (b)  
Remove the lining from the door (AMM 52-13-21/401).

 (c)  
Remove the plate from the handle mechanism.

 
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 SERVICING(118)