曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

R  releases). 
R  (q) Remove the assembly from the crimping tool. 
R  (r) Do the same operation for the other end of the sleeve from step 
R  (m). 
R  (s) Do a check to make sure that the sleeves are in the correct 
R  position. 
R  (t) Do the same operation for the other wires of the cable from step 
R  (f) (the splices must be staggered). 
R  (u) Turn the solder sleeve when you engage it on the screened sleeve 
R  so that it does not catch on the strands. 
R  (v) Center the solder on the screened sleeve and shield. 
R  (w) Heat the center of the sleeve (do not turn the assembly when you 
R  do this) until the sleeve shrinks (the solder ring melts and 
R  flows into the strands of the screened sleeve and shield). 
R  (x) Let cool for a few seconds. 
R  (y) Do the operation again for the other side from step (u). 
R  (z) Install the heat-shrink sleeve. 
R  (aa) Shrink the sleeve.
R  ____NOTE : PTFE requires a minimum temperature of 327 deg.C (620.60 
R  deg.F) for the shrinking. At level of the two solder 
R  sleeves, it is necessary to prevent overheat of the 
R  solder.

 

R 
R  B. Allocation Table of Heat-Shrink Repair Sleeves 
R  (Ref. Fig. 009, 010, 011)
 The table that follows gives the different types of sleeves that you can
 use for repair, in relation to the type and gauge of the cable (Refer to
 chapter 20-42-12 for SLEEVE SHRINKING PROCEDURE).
 ____NOTE : Make sure you use the correct sleeve for the aircraft temperature
 zone. 
R 
R  C. Allocation Table of Solder Repair Sleeves 
R  (Ref. Fig. 012, 013) 
R  The tables that follows gives the size of solder sleeves that you can use 
R  for repair, in relation to the type and gauge of the cable (Refer to 
R  chapter 20-42-12X for SLEEVE SHRINKING PROCEDURE).
 ____NOTE : Make sure you use the correct sleeve for the aircraft temperature
 zone. 
R  D. Allocation Table of Repair Splices 
R  (Ref. Fig. 014) 
R  The table that follows gives the different types of splices you can use 
R  for repair, in relation to the type and gauge of the cable (Refer to 
R  chapter 20-43-1X for SPLICE CRIMPING PROCEDURE).
R  ____NOTE : Make sure you use the correct sleeve for the aircraft temperature 
R  zone.
R  ____NOTE : For more data, refer to 20-53-29 GENERAL REPAIR PROCEDURE.

 

R Repair Sleeves for Unscreened Low-Temp Cables - Allocation Table R Method 4B only R Figure 009

20-53-25 Page 17

R Repair Splices - Allocation Table R Method 2B only R Figure 010

20-53-25 Page 18

R Repair Sleeves for Aluminum Feeder Cables - Allocation Table Method 4B only
R Figure 011

20-53-25 Page 19

R Solder Repair Sleeves - Allocation Table R Methods 2C/2E Only R Figure 012

20-53-25 Page 20

R Solder Repair Sleeves - Allocation Table R Methods 2C/2E Only R Figure 013

20-53-25 Page 21

R Repair Splices - Allocation Table R AD, QP, YU and YV R Figure 014

20-53-25 Page 22

 ___________________________________________________________
REPAIR OF FIRE-RESISTANT CABLES - DESCRIPTION AND OPERATION
 _______
1. General This chapter gives the technical requirements for repair of the cables:
 -
Fire-Resistant Cable with Glass Fiber Braid External Insulation This cable installed on aircraft has P/N: NSA935132 DJ

 -
Fire-Resistant Cable with PTFE Tape External Insulation
 These cables installed on aircraft have P/Ns:
 ABS0053 PL

 

R E0437 or EN2346-003A DL
 ______________________2. Damage Check Procedure
 A. Fire-Resistant Cable with Glass Fiber Braid External Insulation
 (1)
 Cable layout
 (Ref. Fig. 001)

 (2)
 Table for damage assessment
 (Ref. Fig. 001)

 

 B. Fire-Resistant Cable with PTFE Tape External Insulation
 (1)
 Cable layout
 (Ref. Fig. 002)

 (2)
 Table for damage assessment
 (Ref. Fig. 002)

 

 ________________3. Repair Procedure
 A. Procedure (Ref. Fig. 003, 004) This paragraph gives the general description and conditions of application for each repair type.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 ESPM Electrical Standard Practices Manual 4(79)