(2)
Wire Crimping
(Ref. Fig. 017)
-Install the pin/socket contact in the positioner.
-Engage the stripped wire in the pin/socket.
-Make sure that you can see the wire conductor through the pin/socket hole.
-Fully close the tool handles until the safety ratchet releases.
-Remove the crimped contact.
-If sealing is necessary :
-heat shrink the sleeve installed before stripping.
(3)
Contacts Insertion/Extraction
(Ref. Fig. 015)
The tools and standard process are discribed in the relevant
insertion/extraction tool chapter.
D. Clip Replacement DEUTSCH connectors (except size 8) incorporate removable contact retaining clips which can be replaced in case of damage. Replacement clips are identified as follows : 0143-013-000 for size 20 0143-004-000 for size 16.
20-48-23 Page 25
_________________________________________________________7. Connection Procedure for Contacts NSA938164 and NSA938165
A. Contacts P/N and Characteristics
(Ref. Fig. 018) ---------------------------------------------------------------------| | USE WITH | | CONTACTS |------------------------------------------------| | | PLUG | RECEPTACLE | |------------------|-------------------------|----------------------|
R | NSA938164 | E0077 | E0079 (ex NSA938110) | R | NSA938165 | (ex NSA938108) | E0110 (ex NSA938109) | ---------------------------------------------------------------------
B. Contacts Insertion / Extraction Tools
(Ref. Fig. 019)
C. Wire Stripping
(Ref. Fig. 020, 021)
-If sealing is necessary, install the heat-shrinkable sleeve on the wire before stripping. (Shrinking is made after crimping).
-Select the applicable tool.
-Strip the wire at the length "A".
D. Crimping Procedure and Tools
(Ref. Fig. 022)
(1)
If necessary, install the reducer on the conductor.
(2)
Engage the stripped wire in the pin/socket.
(3)
Make sure that you can see the conductor through the pin/socket hole.
(4)
Install the pin/socket contact in the positioner.
(5)
Fully close the tool handles until the safety ratchet releases.
(6)
Remove the crimped contact.
(7)
If sealing is necessary
(a) heat shrink the sleeve installed before stripping.
20-48-23 Page 26
Normal Contacts - P/N Characteristics
NSA938164 and NSA938165
Figure 018
20-48-23 Page 27
Normal Contacts - Insertion/Extraction Tools
NSA938164 and NSA938165
Figure 019
20-48-23 Page 28
Normal Contacts - Shrinking, Stripping and Tools
NSA938164 and NSA938165
Figure 020
20-48-23 Page 29
Normal Contacts - Sleeve Allocation
NSA938164 and NSA938165
Figure 021
20-48-23 Page 30
Normal Contacts - Crimping Tools
NSA938164 and NSA938165
Figure 022
20-48-23 Page 31
__________________________________________________________________________
8. Connection Procedure for Contacts NSA938182, NSA938183, CANNON and SOURIAU Contacts
A. Contacts P/N and Characteristics
(Ref. Fig. 023) ---------------------------------------------------------------------| | USE WITH | | CONTACTS |----------------------------------------------| | | PLUG | RECEPTACLE | |--------------------|-----------------------|----------------------| | NSA938182 | | | | NSA938183 | | | |CANNON 030-2111-000 | | E0098 | |CANNON 031-1194-000 | E0378 | NSA938930 | |SOURIAU 8950-5883 | | | |SOURIAU 8950-6022 | | | ---------------------------------------------------------------------
B. Wire Stripping
(Ref. Fig. 024)
(1) Normal wire
-If sealing is necessary, install the heat-shrinkable sleeve on the wire before stripping. (Shrinking is made after crimping).
-Select the applicable tool.
-Strip to the length "A".
C. Crimping Procedure and Tools
(Ref. Fig. 024)
(1) For E0378 and E0098 with wire gauge 00 to 0000.
(a)
For E0378, cut and remove the lockwire from the connector.
(b)
For E0098, remove the four screws from the square flange on the receptacle.
(c)
For E0378 and E0098:
-Unscrew the backshell (1) and slide it over the wire bundle.
-
Remove the housing (8) towards the front of the connector.
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 ESPM Electrical Standard Practices Manual 4(32)
