R Layout and Table for Damage Assessment R HA, HB, HC, HP, ML, SE, ST, TG, TT, UE, UG, VJ, VR, YD, YF, YK and YT R Figure 005
20-53-22 Page 7
R Layout and Table for Damage Assessment R HA, HB, HC, HP, ML, SE, ST, TG, TT, UE, UG, VJ, VR, YD, YF, YK and YT R Figure 006
20-53-22 Page 820-53-22 Page 9
R (3) When the repair type is selected, refer to :
R R (a) Para. 3 Repair Procedure for the general description and conditions of application.
R (b) 20-53-29 GENERAL REPAIR PROCEDURE for more data .
R D. Cables, with coating
R (1) Cable layout (Ref. Fig. 007, 008)
R (2) Table for damage assessment (Ref. Fig. 007, 008)
(3) When the repair type is selected, refer to :
(a) Para. 3 Repair Procedure for the general description and condition of application.
(b) 20-53-29 GENERAL REPAIR PROCEDURE for more data.
R Layout and Table for Damage Assessment R ST-U, TT-U and UE-U R Figure 007
20-53-22 Page 10
R Layout and Table for Damage Assessment R ST-U, TT-U and UE-U R Figure 008
20-53-22 Page 1120-53-22 Page 12
________________3. Repair Procedure
A. Procedure This paragraph gives the general description and conditions of application for each repair type.
R (1) Method 2A - Wrapping with PTFE tape Material No 05-116 (Ref. Fig. 009) Ref. 20-53-29 for detailled procedure
R (2) Method 2B - Heat-Shrink Sleeve Insulating (Ref. Fig. 009)
R Repair of Screened Cables - Repair Procedure Table R Figure 009
20-53-22 Page 13
(3) Method 2C
R (Ref. Fig. 009)
(a)
Disconnect the cable end.
(b)
Install the heat-shrink sleeve.
(c)
Install the two solder sleeves.
(d)
Engage the solder sleeve on the cable and the shielding link (wire CF 22).
(e)
Turn the solder sleeve when you engage it on the bonding wire so that it does not catch the strands.
(f)
Center the solder on the stripped portion of the bonding wire and shield.
(g)
Heat the center of the sleeve (do not turn the assembly when you do this) until the sleeve shrinks (the solder ring melts and flows into the strands of the bonding wire and shield).
(h)
Let cool for a few seconds.
(i)
Do the operation again for the other side from step (d).
(j)
Install the heat-shrink sleeve.
(k)
Shrink the sleeve.
____
NOTE : PTFE requires a minimum temperature of 327 deg.C (620.60 deg.F) for the shrinking. At level of the two solder sleeves, it is necessary to prevent overheat of the solder.
20-53-22 Page 14
(4) Method 2D
R (Ref. Fig. 009, 010)
(a)
Disconnect the cable end.
(b)
Install the heat-shrink sleeve.
(c)
Install the two solder sleeves.
(d)
Install the screened sleeve.
(e)
Turn the solder sleeve when you engage it on the screened sleeve so that it does not catch the strands.
(f)
Center the solder on the screened sleeve and shield.
(g)
Heat the center of the sleeve (do not turn the assembly when you do this) until the sleeve shrinks (the solder ring melts and flows into the strands of the screened sleeves and shield).
(h)
Let cool for a few seconds.
(i)
Do the operation again for the other side from step (e).
(j)
Install the heat-shrink sleeve.
(k)
Shrink the sleeve.
____
NOTE : PTFE requires a minimum temperature of 327 deg.C (620.60 deg.F) for the shrinking. At level of the two solder sleeves, it is necessary to prevent overheat of the solder.
20-53-22 Page 15
Repair of Screened Cable - Layout Methods 2D/2F R Figure 010
20-53-22 Page 16
(5) Method 2E
R (Ref. Fig. 011)
(a)
Cut the cable and wires.
(b)
Install the heat-shrink sleeve.
(c)
Install the two solder sleeves.
(d)
Install the splice insulation sleeve(s) and if applicable the adapters, on each wire.
(e)
Put one end of the splice in the applicable crimping tool die.
(f)
Hold the splice in the correct position with the positioner.
(g)
Put the stripped end of the wire in the splice barrel.
(h)
Crimp the splice (fully tighten the handle until the ratchet releases).
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 ESPM Electrical Standard Practices Manual 4(73)
