(2)
 Strip the wire to the length A, B, C.

 D. Crimping Procedure and Tools
 (Ref. Fig. 006)

 (1) Slide the internal ferrule (3) under the braided shield (2) until stop.

20-48-32 Page 8

R Coaxial Contacts - P/N Characteristics E0305 Figure 005

20-48-32 Page 9

R Coaxial Contacts - Stripping and Crimping Tools E0305 Figure 006

20-48-32 Page 10

 (2)
 Put the dielectric (4) in the contact body (5).

 (3)
 Solder the contact core.

 (4)
 Slide the external ferrule (1) on the braided shield until it touches the internal ferrule (3).

 (5)
 Install the extraction system (6) on the contact body (5).

 (6)
 Crimp the ferrule (1) with the appropriate tool in the crimping zone

 D.

20-48-32 Page 11
 Apr 01/05
R  ____________________________________________________5. Connection Procedure for E0375 Coaxial Contacts type

 A. A Type E0375 and AMP225936-2
 (1) Contact P/N and characteristics (Ref. Fig. 007) ---------------------------------------------------------------------| | USE WITH | | CONTACTS |------------------------------------------------| | | PLUG | RECEPTACLE | |------------------|-------------------------|----------------------|
R  | A type | E0086 | |
R  | E0375 | E0726 | | |--------------------------------------------| -----| | AMP225936-2 | E0726 | | ---------------------------------------------------------------------
(2)
 Contact insertion / extraction tools
 (Ref. Fig. 007)

 (3)
 Wire stripping procedure
 (Ref. Fig. 008)

 (a) Install the outer sleeve (1) on the cable.
 CAUTION : MAKE SURE THAT YOU DO NOT CUT THE BRAIDED SHIELD OR CAUSE DAMAGE TO THE CENTER CONDUCTOR WHEN YOU STRIP THE CABLE.
 (b)
 Strip the cable to the length A.

 (c)
 Strip the center conductor to the length C.

 (d)
 Cut the braided shield to the length B. Make sure that you do not damage the conductor.

 (4) Crimping procedure and tools
 (Ref. Fig. 009)

 (a)
 Install the contact (2) on the center conductor (3).

 (b)
 Crimp or solder the contact (2) with the applicable tool.

 (c)
 Slide the contact in the ferrule (4). Make sure that the braided shield is on the contact of the ferrule (4).

 (d)
 Slide the sleeve (1) on the zone of the braided shield.

20-48-32 Page 12

R Coaxial Contacts - P/N Characteristics - Insertion/Extraction Tools A Type E0375 and AMP225936-2 Figure 007

20-48-32 Page 13

R Coaxial Contacts - Wire Stripping A Type E0375 and AMP225936-2 Figure 008

20-48-32 Page 14

R Coaxial Contacts - Crimping Tools A Type E0375 and AMP225936-2 Figure 009

20-48-32 Page 15

 (e) Crimp the sleeve (1) with the applicable tool.

 B. B Type E0375
 (1)
 Contact P/N and characteristics ---------------------------------------------------------------------| | USE WITH | | CONTACTS |------------------------------------------------| | | PLUG | RECEPTACLE | |------------------|-------------------------|----------------------| | B type | E0086 | | | E0375 | | NSA938323 | | | NSA938323 | | ---------------------------------------------------------------------

(2)
 Contact insertion / extraction tools
 (Ref. Fig. 010)

 (3)
 Wire stripping procedure
 (Ref. Fig. 011)

 CAUTION : MAKE SURE THAT YOU DO NOT CUT THE BRAIDED SHIELD OR CAUSE DAMAGE TO THE CENTER CONDUCTOR WHEN YOU STRIP THE CABLE.
 (a)
 Slide the sleeve (1) on the cable.

 (b)
 Strip the cable to the length A.

 (c)
 Cut the braided shield to the length B.

 (4) Crimping procedure and tools
 (Ref. Fig. 012)

 (a)
 Open the braided shield in cone form.

 (b)
 Slide the ferrule (2) under the braided shield until the stop.

 (c)
 Slide the sleeve (1) in contact with the braided shield (3).

 (d)
 Make sure that the length C is correct.

 (e)
 Install the center conductor (5) in the dielectric (4).

 (f)
 Make sure that the length D is correct.

 (g)
 Slide a contact (6) in the center conductor.

 (h)
 Solder the contact on the center conductor.

20-48-32 Page 16
 Apr 01/05
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 ESPM Electrical Standard Practices Manual 4(47)