R Normal Contacts - P/N Characteristics R ABS1380 and ABS1381 R Figure 001
20-48-24 Page 2
R Normal Contacts - Insertion/Extraction Tools R ABS1380 and ABS1381 R Figure 002
20-48-24 Page 3
R Normal Contacts - Wire Stripping and Tools R ABS1380 and ABS1381 R Figure 003
20-48-24 Page 4
R Normal Contacts - Wire Stripping R ABS1380 and ABS1381 R Figure 004
20-48-24 Page 520-48-24 Page 6
R D. Insulation procedure
R (Ref. Fig. 003)
R (1) For wire gauges 08 to 04 only:
R (Ref. Fig. 004)
R - Slide the sleeve E0718 until it is level with the stripped wire and
R shrink it.
R - Shrink the sleeve NSA937502 at the rear and on the sleeve E0718.
R - Make sure that the sealing sleeve (e.g ABS0992) is installed before
R crimping.
R E. Crimping Procedure
R (Ref. Fig. 005, 006)
R - Make sure that the sleeve E0718 (if installed) is shrunk on the wire.
R - Engage the stripped wire in the contact (for gauges 08 to 04 only, use
R lubricant HELLERINE or equivalent on the end of the sleeve).
R - Install the contact in the positioner.
R - Select the applicable tool.
R - Install the contact in the positioner.
R - Fully close the tool handles until the safety ratchet releases.
R - Remove the crimped contact.
R - Make sure that the contact crimping is correct.
R - Make sure that the length C (colored mark) is correct.
R - If installed, slide the sealing sleeve on the contact.
R Normal Contacts - Crimping Tools R ABS1380 and ABS1381 R Figure 005
20-48-24 Page 7
R Normal Contacts - Crimping Tools R ABS1380 and ABS1381 R Figure 006
20-48-24 Page 820-48-24 Page 9
R _________________________________________________________________________3. Connection Procedure for Contacts E0445, E0446, EN3155-004 and EN3155-005
R A. Contact P/N and Characteristics
R (Ref. Fig. 007)
R ---------------------------------------------------------------------
R | | USE WITH |
R | CONTACT |------------------------------------------------|
R | | PLUG | RECEPTACLE |
R |------------------|-------------------------|----------------------|
R | E0445 | E0441 | |
R | E0446 | E0442 | E0444 |
R | EN3155-004 | EN2997 | EN2997 |
R | EN3155-005 | | |
R ---------------------------------------------------------------------
R B. Temperature
R Minimum operating temperature is -65 deg.C (-85.00 deg.F).
R Maximum operating temperature is 260 deg.C (500.00 deg.F).
R C. Contact Insertion/Extraction Tools
R (Ref. Fig. 008)
R D. Wire Stripping
R (1) Normal wires
R (Ref. Fig. 009, 010, 011)
R - If necessary install the heat shrinkable sleeve on the wire before
R stripping.
R Shrinking is done after crimping.
R - Use the applicable tool.
R - Strip the wire to the length "A".
R (2) Special wires
R (Ref. Fig. 009)
R E0437 DL22 and DL20
R NSA935132 DJ20
R - Remove the fiberglass braid then the PTFE envelope along a length
R of 50 mm (1.9685 in.).
R - Strip the core cable along a length of 35 mm (1.3779 in.).
R - Install the heat shrinkable sleeve NSA937210MB0200 on the outer
R sheath along 10 mm (0.3937 in.) and shrink.
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 ESPM Electrical Standard Practices Manual 4(35)
