曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

R  | ---------------- Terminal 
R  | 
R  ------------------------ Standard P/N 
R  (2) P/N Characteristics 
R  (a) Temperature 
R  Minimum operating temperature is -55 deg.C (-67.00 deg.F). 
R  Maximum operating temperature is 260 deg.C (500.00 deg.F). 
R  (3) Connection Procedure 
R  (a) Stripping Procedure 
R  (Ref. Fig. 017, 018) 
R  - Select the applicable tool. 
R  - Install the sleeve(s) on the wire. 
R  - Strip the wire to the length "A". 
R  (b) Crimping Procedure 
R  (Ref. Fig. 018, 019) 
R  - Select the applicable tool. 
R  - Install the terminal in the tool. 
R  - Slightly operate the tool to hold terminal in position. 
R  - Engage the stripped wire in the terminal. 
R  - Fully operate the tool until safety ratchet releases. 
R  (c) Insulation Procedure 
R  (Ref. Fig. 017, 018) 
R  Method 1 
R  - Select the applicable tool. 
R  - Install and retract the shrinkable sleeve (1) on the terminal. 
R  Method 2 
R  - Select the applicable tool. 
R  - Install and retract the shrinkable sleeve (2) on the terminal. 
R  - Wait until the sleeve (2) is fully cool.

 

 Copper Wire Terminals - Allocation Table
 NSA936507
 Figure 017

20-48-11 Page 26
 Apr 01/05
R

 Copper Wire Terminals - Tools
 NSA936507
 Figure 018

20-48-11 Page 27
 Apr 01/05
R

 Copper Wire Terminals - Tools
 NSA936507
 Figure 019

20-48-11 Page 28
 Apr 01/05
R

R  - Install and retract the shrinkable sleeve (3) on the terminal.
 ___________________________________7. Rectangular Slotted Tongue Terminal
 A. NSA936510 (Ref. Fig. 020)
 (1) P/N identification NSA936510 - T K 16 03 | | | | | | | | | ---------------- Range | | | | | | | ------------------- AWG Wire gauge | | | | | --------------------- Type code | | | ----------------------- Terminal | ------------------------------- Standard P/N
 (2) P/N characteristics
 (a) Temperature Minimum operating temperature is -55 deg.C (-67.00 deg.F). Maximum operating temperature is 105 deg.C (221.00 deg.F). 
R  (3) Connection Procedure 
R R R R R R R  (a) Stripping Procedure (Ref. Fig. 020) - Slide the 35 mm (1.3779 in.) long heat shrinkable sleeves NSA937502-03 on each cable for the insulation of the terminals. Do the shrinking operation after connection to the connector. - Select the applicable stripping tool. - Strip the cable at the length "A". 
R R R R R R R R R R  (b) Crimping Procedure (Ref. Fig. 020) - Select the applicable crimping tool. - Put the terminal at the center between the tool dies. If you can see the brazing seam, put it at the center opposite to the punch. - Squeeze the tool handles to hold the terminal in crimping position. - Engage the stripped cable in the terminal and make sure that all the strands are engaged.

 

20-48-11 Page 29

R Copper Wire Terminals - Tools NSA336510 Figure 020

20-48-11 Page 3020-48-11 Page 31

R  - Fully close the tool handles until the ratchet releases and the 
R  dies opens automatically. 
R  - Remove the crimped assembly from the tool. 
R  - Make sure that the connection is in the correct condition and 
R  that : 
R  * The cable insulator does not go into the barrel. 
R  * The crimping indents are centered. 
R  * The stripped conductors do not protrude to much (visible 
R  length < 1.5 mm (0.0590 in.)). 
R  (c) Insulation Procedure 
R  (Ref. Fig. 020) 
R  - Select the applicable shrinking tool. 
R  - Slide the terminal insulation in position : the sleeve must 
R  cover the cable and the terminal up to the screw for connection 
R  attachment. 
R  - Shrink the sleeve.
 _________________8. Wire Pin Terminal
 A. ABS0909
 (Ref. Fig. 021)
 (1) P/N identification
 ABS0909 -01
 | |
 | ----------------------- Size code
 ------------------------------- Standard P/N
 (2) P/N characteristics
 (a) Temperature
 Minimum operating temperature is -55 deg.C (-67.00 deg.F).
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 ESPM Electrical Standard Practices Manual 4(17)