C. Expendable Parts -------------------------------------------------------------------------------
FIG.ITEM --------- |DESIGNATION ---------------------------------------- |IPC-CSN------------------------------
52 lockwasher 56-12-11 02A-185
53 lockwasher 56-12-11 02A-185
54 lockwasher 56-12-11 03C-185
55 lockwasher 56-12-11 03C-185
D. Referenced Information
------------------REFERENCE -------------------------------DESIGNATION ------------------------------
-------------------------------------------------------------------------------
30-42-00-710-001 Operational Test of the Windshield Anti-Icing and
Defogging 33-12-12-400-002 Installation of the Map Table lights (41LE, 42LE) 33-12-18-400-001 Installation of the Map Table Light Rheostats (39LE,
40LE) 52-10-00-410-001 Closing of the Passenger/Crew Door 56-10-00-110-003 Cleaning of the L/R Sliding Windows 56-12-11-410-001 Closing of the Cockpit Sliding Windows 56-12-11-991-071 Fig. 417 56-12-11-991-072 Fig. 418 56-12-11-991-073 Fig. 419 56-12-11-991-074 Fig. 420
3. Job Set-up
__________
Subtask 56-12-11-860-052
A. Aircraft Maintenance Configuration
(1)
Make sure that the access platforms are in position.
(2)
Make sure that the FWD passenger/crew door is open.
R 1EFF : 001-049, 101-149, 151-199, 201-299, 1 56-12-11Page 491 1301-399, 401-499, 1Aug 01/05 1 1 1CES 1
Subtask 56-12-11-865-066
B. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------
121VU COM NAV/RADAR/1 5SQ1 K13
FOR 8DG1 122VU ANTI ICE/WINDOWS/L 4DG1 X14 122VU ANTI ICE/WHC/1 5DG1 X13 123VU ANTI ICE/L/WHSLD 1DG1 AF10
FOR 8DG2 122VU ANTI ICE/WINDOWS/R 4DG2 W14 122VU ANTI ICE/WHC/2 5DG2 W13 123VU ANTI ICE/R/WHSLD 1DG2 AF03
4. Procedure
_________
Subtask 56-12-11-110-063
A. Preparation for Installation
(1) Clean the housing of the sliding window panel with CLEANING AGENTS (Material No. 11-003) and MISCELLANEOUS (Material No. 19-003).
Subtask 56-12-11-420-067
B. Installation of the Sliding Window Panel
CAUTION : BE CAREFUL DURING THE REMOVAL/INSTALLATION OF EACH SLIDING
_______ WINDOW PANEL TO PREVENT INJURY TO PERSONS AND /OR DAMAGE. MAKE SURE THAT THERE ARE SUFFICIENT PERSONS DURING THE OPERATION. EACH WINDOW PANEL WEIGHS APPROXIMATELY 20Kg (44.11b).
(1) Installation of the acrylic sliding window panel (LUCAS/ACT supplier, P/N NH...) and glass sliding window panel (PPG supplier, P/N NH...). (Ref. Fig. 418/TASK 56-12-11-991-072)
NOTE : The attachment holes on the periphery of the window panel are
____
identified by numbers 1 to 63.
(a) Use 2 suction cups to move and hold the sliding window panel (31) in position during installation in its frame.
R 1EFF : 001-049, 101-149, 151-199, 201-299, 1 56-12-11Page 492 1301-399, 401-499, 1Aug 01/05 1 1 1CES 1
(b)
Put the sliding window panel (31) in position in its housing.
(c)
Move the frame of the sliding window to the closed position.
(d)
Installation of the pins:
(e)
Move the frame of the sliding window to the open position.
(f)
Do a check of the interface clearance C between the sliding window panel (31) and the frame (33). (Ref. Fig. 420/TASK 56-12-11-991-074)
1_ For the acrylic sliding windows (LUCAS/ACT supplier P/N
NH...), install 2 locating pins dia. 5.5 mm (0.19 in.), length
50 mm (1.96 in.) at positions 28 and 60 to hold the sliding
window panel (31) in position.
2_ For the glass sliding windows (PPG supplier, P/N NP...),
install 2 locating pins dia. 4.8 mm (0.19 in.), length 50 mm
(1.96 in.) at positions 28 and 60 to hold the sliding window
panel (31) in position.
1 Make sure that the interface through-clearance C is 2 mm
_ (0.0787 in.) maximum.
NOTE : The check of the interface clearance C is not
____ applicable for the acrylic sliding window (LUCAS/ACT supplier, P/N NH...).
(g)
Install the screws (32) and the nuts (30). Do not install screws at positions 28 and 60.
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM WINDOWS 風擋 窗戶(70)
