(b)
 The load permitted on the handle is 20 +2 -3 daN (44.9617 +4.4961 -6.7442 lbf) . If the load is not in the tolerance, adjust the sliding window again.

R 1EFF : 001-049, 101-149, 151-199, 201-299, 1 56-12-11Page 453 1301-399, 401-499, 1Aug 01/05 1 1 1CES 1 NOTE : We recommend that you adjust the window to get a load on

____ the handle near the maximum limit.
 **ON A/C 001-049, 101-101,
 Subtask 56-12-11-820-057
 E. Check of Locking of the Sliding Window in the Open Position
 (Ref. Fig. 413/TASK 56-12-11-991-079)

 (1)
 When you fully open the window, make sure that the locking lever

 (101) engages in the rack (102).

 (2)
 If the locking lever (101) does not engage in the rack (102), do the steps that follow:

 (a)
 Remove the lockwire and loosen the nuts (105).

 (b)
 Turn the rod (103) until the locking lever (101) engages in the rack (102).

 (c)
 Tighten the nuts (105).

 (d)
 Safety the nuts (105) with MISCELLANEOUS (Material No. 19-010).

 (3)
 If the locking lever (101) does not engage after these steps:

 (a)
 Remove the circlip (106).

 (b)
 Loosen the nut (107).

 (c)
 Turn the eccentric (108) until the locking lever (101) engages in the rack (102).

 (d)
 Make sure that the clearance J7 between the rack (102) and the side of the rail (104) is 0.5 mm (0.0196 in.) minimum. If the clearance J7 is not in the tolerance, turn the rod until the locking lever (101) engages in the rack (102).

 (e)
 TORQUE the nut (107) to between 0.4 and 0.5 m.daN (35.39 and

 44.24 lbf.in).

 (f)
 Safety the nut (107) with BONDING AND ADHESIVE COMPOUNDS (Material No. 08-002A).

 (g)
 Install the circlip (106).

R 1EFF : 001-049, 101-149, 151-199, 201-299, 1 56-12-11Page 454 1301-399, 401-499, 1Aug 01/05 1 1 1CES 1

 (4) Do a check of the adjustment in the X and Y axis. R **ON A/C 001-049, 101-149, 151-199, 201-299, 301-399, 401-499,
 Subtask 56-12-11-210-065
 F. Sealing Check
 (1)
 Close the sliding window

 (2)
 Apply water to the periphery of the sliding window from the outside of the aircraft

 (3)
 Wait ten minutes and make sure that there is no water leakage at level of the window frame.

 (4)
 If water goes into the cockpit, make sure that the adjustments are correct and that the seal is in the correct condition.

 (5) Dry if necessary.
 Subtask 56-12-11-914-053

 G. Installation of the Aft Upper Rail
 (Ref. Fig. 409/TASK 56-12-11-991-067)

 (1)
 Remove the nuts (57) the bolts (54), (55) and the aft upper rail (56).

 (2)
 Apply a light coat of SEALANTS (Material No. 09-019) between the upper surface of the rail (56) and the frame.

 (3)
 Install the aft upper rail (56) on its support.

 (4)
 Install the bolts (54),(55) the nuts (57) and tighten them.

 (5)
 Remove the film that protects the sliding window.

R 1EFF : 001-049, 101-149, 151-199, 201-299, 1 56-12-11Page 455 1301-399, 401-499, 1Aug 01/05 1 1 1CES 1

 Sliding Window - Check of Locking in Open Position R Figure 413/TASK 56-12-11-991-079- 12 (SHEET 1)
R 1EFF : 001-049, 101-101, 1 56-12-11Page 456 1 1 May 01/05 1 1 1CES 1

 Sliding Window - Check of Locking in Open Position R Figure 413/TASK 56-12-11-991-079- 22 (SHEET 2)
R 1EFF : 001-049, 101-101, 1 56-12-11Page 457 1 1 May 01/05 1 1 1CES 1

 Subtask 56-12-11-420-065

 H. Installation of the Linings Panels (Ref. Fig. 407/TASK 56-12-11-991-065, 408/TASK 56-12-11-991-066)
 (1) Installation of the sliding window lining (16)
 (a)
 Remove the blanking caps from the electrical connectors.

 (b)
 Connect the sensor (10).

 (c)
 Lift the plate (17) and put the sliding window lining (16) in position.

 (d)
 Put the plate (17) in position, install the screws (12) and tighten them.

 (e)
 Install the screws (11) and tighten them.

 (f)
 Install the washer (2) and the screw (3).

 (g)
 Tighten the screw (3).

 (h)
 Install the blanking plug (4).

 (i)
 Open the sliding window.

 (j)
 Install the guide (13) on the sliding window lining (16) with the washer (14) and the screw (15).
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM WINDOWS 風擋 窗戶(61)